Journals →  Chernye Metally →  2024 →  #7 →  Back

Machine-building technologies
ArticleName Bending of steel multilayer sheet material
DOI 10.17580/chm.2024.07.13
ArticleAuthor S. A. Tipalin, B. Yu. Saprykin, N. D. Borisov
ArticleAuthorData

Moscow Polytechnic University, Moscow, Russia

S. A. Tipalin, Cand. Eng., Prof., Dept. of Metalworking and Additive Technologies (OMD&AT), e-mail: tsa_mami@mail.ru
B. Y. Saprykin, Senior Lecturer, Dept. of OMD&AT, e-mail: saprykin-boris@mail.ru
N. D. Borisov, Postgraduate Student, Dept. of OMD&AT, e-mail: nicbor1998@gmail.com

Abstract

The calculation of technological parameters and the prediction of the behavior of the workpiece during deformation are directly interrelated with the properties of the material. The use of multilayer steel sheets with a connecting elastic-viscous layer changes the flow of the layers and radically changes the stress gradients in the deformable material. The use of multilayer materials (steel-polymer-steel) reduces noise and vibration in finished products, which makes the use of data very promising. The paper considers a numerical study of the bending of a billet consisting of two 0.5 mm thick sheet layers of 08 steel connected by an elastic-viscous connecting layer. The thickness of the layer is 0.05 mm and its shear properties were determined experimentally. During the numerical simulation, data were obtained on the distribution of radial and tangential stresses in each metal sheet and the degree of material thinning depending on the relative bending radius of the material. The stress and thinning distributions for multilayer and single-layer materials are compared. During the research, it was revealed that the inner layer of the multilayer sheet increases its thickness during bending, and the outer layer is thinned. At the same time, the degree of intensity of the thinning of the outer layer exceeds the thickening of the inner layer by an order of magnitude. The total thinning of two layers of material is one and a half times higher than the thinning of a single-layer material of the same brand with a similar thickness. A comparison of the bending moment of a two-layer and a single-layer sheet of equal thickness showed that the bending moment of a homogeneous material is approximately twice that of a monolithic workpiece. These features must be taken into account when developing the technological process of bending parts made of multilayer materials.

keywords Multilayer material, layer thickness, thinning of sheet, bending, bending moment, connecting polymer layer, noise-absorption
References

1. Tipalin S. A., Saprykin B. Y., Shpunkin N. F. Overview of the multi-layer sheet deformable materials for protection against noise. Izvestiya of MSTU “MAMI”. 2012. Vol. 2. No. 2 (14). pp. 194–199.
2. Аntiphon® MPMTM structure-borne sound damping laminate. Avaiulable at: https://antiphon.se/en/products-and-applications/mpm-structure-borne-sound-damping-laminate

3. Tipalin S. A., Shpunkin N. F., Nikitin M. Y., Tapilina A. V. Experimental investigation of mechanical properties of damping material. Izvestiya of MSTU “MAMI”. 2010. No. 1 (9). pp. 166 170.
4. Tipalin S. A., Shpunkin N. F., Saprykin B. Y. Determination of properties of sheet damping material with viscoelastic coupling layer during shear deformation. Izvestiya of MSTU “MAMI”. 2014. Vol. 2. No. 2(20). pp. 99–103.
5. Temnikova N. E., Rusanova S. N., Stoyanov O. V. Adhesive compound steel-adhesive-steel based on modified ethylene copolymers. Vestnik Kazanskogo Tehnologicheskogo Universiteta. 2014. Vol. 17. No. 7. pp. 151–153.
6. Abdurakhmanov A. A., Bogacheva V. E., Glagolev V. V. To evaluating the limit state of the adhesion layer in a layered composite. Mehanika Kompozicionnyh Materialov i Konstrukcij. 2020. Vol. 26. No. 2. pp. 247–258.
7. Matveev A. D. Plastic bending of the sheet at constant thickness. Izvestiya vuzov. Mashinostroenie. 1983. No. 1. pp. 12–18.
8. Bondar V. S., Tipalin S. A., Shpunkin N. F. Bending and twisting of sheet. Moscow : Universitet Mashinostroeniya, 2014. 212 p.
9. Gnevashev D. A., Orudzhev S. F. Study of the process of bending long sheet products with selection of pressure dies based on computer modeling. Chernye Metally. 2023. No. 11. pp. 47–52.
10. Shatalov R. L., Maksimov E. A. Analysis of asymmetric rolling efficiency for improving rolled strip accuracy. Metallurgist. 2016. Vol. 60. No. 7-8. pp. 730–735.
11. Shatalov R., Maksimov E., Koinov T., Babkin A. Research of flatness defects forming at 20-hi steel strips rolling mill. Journal of Chemical Technology and Metallurgy. 2017. Vol. 52. No. 2. pp. 199–204.
12. Mohammadi S. V., Parsa M. H., Aghchai A. J. Effect of the thickness distribution and setting condition on springback in multi-layer sheet bending. International Journal of Engineering, Science and Technology. 2011. Vol. 3. No. 4. pp. 225–235.
13. Park H., Kim S.-J., Lee J., Kim J. H., Kim D. Delamination behavior analysis of steel/polymer/steel high-strength laminated sheets in a V-die bending test. International Journal of Mechanical Sciences. 2020. Vol. 173. No. 1. 105430.
14. Yang J., Han S., Yu W.-R. Detection of delamination of steel–polymer sandwich composites using acoustic emission and development of a forming limit diagram considering delamination. Heliyon. 2023. Vol. 9. No. 6. e16942.
15. Senol O., Esat V., Darendeliler H. Springback analysis in air bending process through experiment based artificial neural networks. Procedia Engineering. 2014. Vol. 81. pp. 999–1004.
16. Shinkin V.N. Residual curvature of bimetallic sheet at elastoplastic bending. Chernye Metally. 2023. No. 7. рр. 67–70.
17. Shinkin V.N. Elastoplastic flexure of round steel beams. 1. Springback coefficient. Steel in Translation. 2018. Vol. 48. No. 3. pp. 149–153.
18. Pritima D., Veerappan G., Patel V. D., Parthasarathy N. R. Analysis of spring back behaviour during bending of AISI 1045 sheet metal. Materials Today: Proceedings. 2022. Vol. 59. No. 2. pp. 1575–1580.
19. Wang J., Li J., Fu C., Zhang C. et al. Study on influencing factors of bending springback for metal fiber laminates. Composite Structures. 2021. Vol. 261. 113558.
20. Shinkin V. N. Elastoplastic flexure of round steel beams. 2. Residual stress. Steel in Translation. 2018. Vol. 48. No. 11. pp. 718–723.
21. Sharma P. K., Gautam V., Agrawal A. K. Investigations on effect of bending radius on springback behaviour of three-ply clad sheet. Materials Today: Proceedings. 2022. Vol. 62. pp. 1651–1657.

Language of full-text russian
Full content Buy
Back