Journals →  Chernye Metally →  2023 →  #6 →  Back

Foundry Production
ArticleName Increasing the service life of metal injection molds
DOI 10.17580/chm.2023.06.02
ArticleAuthor R. V. Gavariev, I. A. Savin, I. O. Leushin, K. N. Gavarieva.
ArticleAuthorData

Kazan National Research Technical University named after A. N. Tupolev – KAI, Kazan, Russia:
R. V. Gavariev, Cand. Eng., Associate Prof., Dept. of Design and Technologies of Machine-Building Industries, e-mail: gavarievr@mail.ru
I. A. Savin, Cand. Eng., Associate Prof., Head of the Dept. of Design and Technologies of Machine-Building Industries, e-mail: savin.ia@kaichelny.ru

 

Nizhny Novgorod State Technical University named after R. E. Alekseev, Nizhny Novgorod, Russia:
I. O. Leushin, Dr. Eng., Prof., Head of the Dept. of Metallurgical Technologies and Equipment, e-mail: igoleu@yandex.ru

 

Kazan (Volga Region) Federal University, Kazan, Russia:
K. N. Gavarieva, Cand. Eng., Senior Lecturer, Dept. of Design and Technological Support of Machine-Building Industries, e-mail: gavarievakn@mail.ru

Abstract

Injection molding is a high-performance method for producing high-quality castings with a complex external configuration. At the same time, it is characterized by disadvantages associated with the high cost of metal molds, as well as their relative low operational durability. The methods traditionally used in production and in theory to increase operational resistance associated with the optimization of technological processes of casting, as well as the use of expensive materials in combination with various methods of chemical-thermal treatment of the forming surface are considered. The disadvantages of both approaches include the duration and complexity of commissioning and testing work, as well as the need for highly qualified engineering workers, which is often difficult to implement. The article suggests one of the possible ways to increase the durability of foundry equipment by using metal-based coatings applied by physical vapor deposition (PVD) on the forming surfaces of the mold. These coatings have a number of positive features suitable for the conditions of the injection molding process, these include: low thickness, wear resistance, crack resistance, the possibility of using various metals as the basis of the coating. Laboratory studies and industrial experiments were conducted to confirm the effectiveness of the use of PVD coatings in the conditions of the injection molding process. Examination of the sample under a microscope revealed good adhesion of the coating to the material of the mold inserts, as well as chemical inertia in relation to the poured melt. Possible technological difficulties in the manufacture of forming parts of the mold can lead to the appearance of local chips, but do not have a critical impact on the performance of the entire mold. According to the results of the production experiment, the operational durability of forming inserts with a TiCN–TiN–MoN coating applied by the PVD method is 25% higher than the similar index of inserts with nitriding and amounts to 180,000 pressing cycles when casting zinc alloys.

keywords Steel, mold, injection molding, coating, casting, physical vapor deposition, operational life
References

1. Goryunov I. I. Molds for injection molding. Reference book. Leningrad: Mashinostroenie, 1973. 256 p.
2. Zhukov А. А., Nemtyrev О. V., Khasanova L. А. Investigation of corrosion resistance of steels for injection molds. Zagotovitelnye proizvostva v mashinostroenii. 2014. No. 4. pp. 31–35.
3. Gavariev R. V., Gavarieva K. N. The principle of choosing the composition of the protective coating for die casting molds. Defect and Diffusion Forum. 2021. Vol. 410. pp. 495–500. DOI: 10.4028/www.scientific.net/ddf.410.495
4. Belopukhov А. К. Technological modes of injection molding. Moscow: Mashinostroenie, 1985. 272 p.
5. Zhukov А. А., Nemtyrev О. V. Investigation of thermal structural stability of steels for injection molds. Naukoemkie tekhnologii v mashinostroenii. 2014. No. 4 (34). pp. 3–10.
6. Tojal M. C., Silva F. J. G., Campilho R. D. S. G., Pinto A. G., Ferreira L. P. Case-based product development of a high-pressure die casting injection subset using design science research. FME Transactions. 2022. Vol. 50, Iss. 1. pp. 32–44.
7. Borodin I. P., Shiryaev V. Yu., Shatov Yu. S., Sedykh О. V. Restorative heat treatment and repair of metallurgical articles. Remont. Vosstanovlenie. Modernizatsiya. 2012. No. 11. pp. 41–43.
8. Livshits V. B., Milchakova N. Е., Berestnev А. А. Method for hardening mold inserts for injection molding with crystallization. Liteynoe proizvodstvo. 2018. No. 3. pp. 30–32.
9. Schuchardt T., Müller S., Dilger K. A near-surface layer heat treatment of die casting dies by means of electron-beam technology. Metals. 2021. Vol. 11, Iss. 8. 1236. DOI: 10.3390/met11081236
10. Kolesnikov М. S., Mukhametzyanova G. F., Mukhametzyanov I. R. Analog studies of thermomechanical fatigue of surface-hardened steels used for the manufacture of die casting molds for aluminum alloys. Liteyshchik Rossii. 2015. No. 1. pp. 22–27.
11. GOST 5950–2000. Tool alloy steel bars, strips and coils. General specifications. Introduced: 01.01.2002.
12. GOST 25140–93. Zinc alloys for casting. Grades. Introduced: 01.01.1995.
13. Vereshchaka А. S. Performance of cutting tools with wear-resistant coatings. Moscow: Mashinostroenie, 1993. 336 p.
14. Gavariev R. V., Savin I. A., Gavarieva K. N. Determination of properties of wear-resistant coatings of metal forms. Solid State Phenomena. 2021. Vol. 316. pp. 732–737. DOI: 10.4028/www.scientific.net/ssp.316.732

Language of full-text russian
Full content Buy
Back