Journals →  Tsvetnye Metally →  2023 →  #4 →  Back

AUTOMATION OF MINING AND CONCENTRATING PROCESSES
ArticleName The practice of using VAZM-1M analyzer in monitoring and control systems designed for tube mills and mill/cyclone stages
DOI 10.17580/tsm.2023.04.09
ArticleAuthor Sokolov I. V., Morozov V. V., Vasiliev V. V., Lebedik E. A.
ArticleAuthorData

Soyuztsvetmetavtomatika JSC, Moscow, Russia:

I. V. Sokolov, Responsible for Process Control System Deployment at the Engineering Department, e-mail: Sokolov@scma.ru


National University of Science and Technology MISiS, Moscow, Russia:

V. V. Morozov, Professor, Doctor of Technical Sciences, e-mail: dchmggu@mail.ru

 

Saint Petersburg Mining University, Saint Petersburg, Russia:
V. V. Vasiliev, Dean of the Faculty for Postgraduate and Doctoral Studies, Candidate of Technical Sciences, e-mail: Vasilev_VV@pers.spmi.ru
E. A. Lebedik, Assistant Lecturer at the Department of Process and Plant Automation, Candidate of Technical Sciences, e-mail: Lebedik_EA@pers.spmi.ru

Abstract

This paper examines the problem of monitoring of and control over tube mills, which lies in the fact that such mills combine two successive grinding functions – actual grinding of the initial product (1st chamber) and its regrinding to the required size (2nd chamber). It is concluded that each chamber of the tube mill should be controlled separately but synchronously, so that not only the load and process parameters were controlled, but also the two chambers (zones) in their interaction. The paper substantiates that the problem of separate but synchronous control of the chambers (zones) of a tube mill can be solved with the help of a vibroacoustic mill charge analyzer VAZM-1M developed by Soyuztsvetmetavtomatika JSC. The analyzer monitors and controls the mill load based on the correlation between the volume load of the mill (feed material, grinding media, soda solution) and the noise level (based on vibration and/or acoustics). The paper describes the actual performance of the VAZM-1M analyzer when it was used in a single-chamber mill and a two-chamber mill at the facilities of BazelCement-Pikalevo LLC and RUSAL Krasnoturyinsk JSC.

keywords Tube mill, ball mill, filling, performance, vibroacoustic noise, load analyzer, correlation, process load, charging options, chamber, grinding
References

1. Boikov A. V., Savelev R. V., Payor V. A. et al. The control method concept of the bulk material behavior in the pelletizing drum for improving the results of DEM-modeling. CIS Iron and Steel Review. 2019. No. 1. pp. 10–13. DOI: 10.17580/cisisr.2019.01.02
2. Fedorova E., Pupysheva E., Morgunov V. Modelling of red-mud particlesolid distribution in the feeder cup of a thickener using the combined CFDDPM approach. Symmetry. 2022. Vol. 14. DOI: 10.3390/sym14112314
3. Beloglazov I. I., Sabinin D. S., Nikolaev M. Yu. Modeling the disintegration process for ball mills using DEM. Mining Informational and Analytical Bulletin. 2022. No. 6–2. pp. 268–282. DOI: 10.25018/0236_1493_2022_62_0_268
4. Kashin D. A., Kulchitskiy A. A. Image-based quality monitoring of metallurgical briquettes. Tsvetnye Metally. 2022. No. 9. pp. 92–98. DOI: 10.17580/tsm.2022.09.13
5. Shestakov A. K., Petrov P. A., Nikolaev M. Y. Automatic system for detecting visible emissions in a potroom of aluminum plant based on technical vision and a neural network. Metallurgist. 2023. DOI: 10.1007/s11015-023-01445-z
6. Vasilyeva N., Fedorova E., Kolesnikov A. Big data as a tool for building a predictive model of mill roll wear. Symmetry. 2021. Vol. 13. DOI: 10.3390/sym13050859
7. Nguyen H. H., Bazhin V. Y. Optimization of control system for electrolytic copper refining with digital twin during dendritic precipitation. Metallurg. 2023. No. 1. pp. 49–56. DOI: 10.52351/00260827_2023_01_49
8. Bazhin V., Masko O. Monitoring of the behaviour and state of nanoscale particles in a gas cleaning system of an ore-thermal furnace. Symmetry. 2022. Vol. 14. DOI: 10.3390/sym14050923
9. Zhukovskiy Y. L., Korolev N. A., Malkova Y. M. Monitoring of grinding condition in drum mills based on resulting shaft torque. Journal of Mining Institute. 2022. Vol. 256. pp. 686–700. DOI: 10.31897/pmi.2022.91
10. Prokhorenko E., Klepikov V., Lytvynenko V., Khaymovich P. et al. Diagnostics of processes of wear of materials of ball-tube mills. Eastern-European Journal of Enterprise Technologies. 2015. No. 1. DOI: 10.15587/1729-4061.2015.36638
11. Hambric S. A., Sung S. H., Nefske D. J. Engineering vibroacoustic analysis: methods and applications. Engineering Vibroacoustic Analysis: Methods and Applications. 2014. DOI: 10.1002/9781118693988
12. Ulitenko K. Ya., Sokolov I. V., Markin R. P., Naydenov A. P. Automation of comminution processes in concentration and metallurgy. Tsvetnye Metally. 2005. No. 10, Special issue. pp. 54–59.
13. Fahy F., Gardonio P. Sound and structural vibration. Sound and Structural Vibration. 2007. DOI: 10.1016/B978-0-12-373633-8.X5000-5
14. Wada T., Uematsu T., Shiomi H., Osaki K. et al. Prediction of power of a vibration rod mill during cellulose decrystallization processing by DEM. Advanced Powder Technology. 2021. Vol. 32, Iss. 10. DOI: 10.1016/j.apt.2021.08.027
15. Morozov V. V., Topchaev V. P., Ulitenko K. Ya., Ganbaatar Z. et al. Development and application of automated systems of control of mineral dressing processes. Moscow : “Ore and Metals” Publishing House, 2013. pp. 100–106.
16. Feng L., Yang F., Zhang W., Tian H. Model predictive control of duplex inlet and outlet ball mill system based on parameter adaptive particle swarm optimization. Mathematical Problems in Engineering. 2019. DOI: 10.1155/2019/6812754
17. le Roux J. D., Steinboeck A., Kugi A., Craig I. K. Steady-state and dynamic simulation of a grinding mill using grind curves. Minerals Engineering. 2020. Vol. 152. pp. 1–21. DOI: 10.1016/j.mineng.2020.106208
18. Lvov V. V., Chitalov L. S. Modern trends in the design of processes and equipment for grinding of ores of non-ferrous metals. Tsvetnye Metally. 2020. No. 10. pp. 20–26. DOI: 10.17580/tsm.2020.10.03
19. Asbjornsson G., Tavares L. M., Mainza A., Yahyaei M. Different perspectives of dynamics in comminution processes. Minerals Engineering. 2022. Vol. 176. pp. 1–9. DOI: 10.1016/j.mineng.2021.107326
20. Dmitrak Yu. V. Motion of grinding load in ball mills. Vektor GeoNauk. 2021. Vol. 4, No. 1. pp. 28–36. DOI: 10.24411/2619-0761-2021-10003
21. Verdiyan M. A., Golovin E. N., Lesikhina A. I. et al. Partitioned tube mills. Tsement. 1987. No. 7. pp. 20–21.
22. Kremcheev E. A., Kremcheeva D. A. Methodological approaches to controlling the feed breakage process in drum and tube mills based on the results of vibroacoustic diagnostics. Journal of Industrial Pollution Control. 2017. Vol. 33, Iss. 1. pp. 787–791.
23. Strasser S. Current status of the comminution process developed by KHD Humboldt Wedag AG. Tsement i ego primenenie. 2002. No. 1. pp. 27–30.
24. Duda V. Cement. Moscow : Stroyizdat, 1981. 464 p.
25. Lepikhova V. A., Lyashenko N. V., Chibinev N. N., Vyaltsev A. V. et al. Theoretical substantiation of the principles of continuous control of grinding equipment modes at the stage of cereal formation. IOP Conference Series: Earth and Environmental Science. 2022. Vol. 979, Iss. 1. DOI: 10.1088/1755-1315/979/1/012061
26. Adambaev M. D., Baynazarova L. A., Togzhanova Zh. K. A method of coherent by-chamber feed control for two-chamber separator mill and a device to implement it. Certificate of authorship RK, No. 15804. Published: 15.06.2005.
27. Litvinenko V. S., Petrov E. I., Vasilevskaya D. V., Yakovenko A. V. et al. Analyzing the role of the state in the mineral resources management. Journal of Mining Institute. 2023. Vol. 259. pp. 95–111. DOI: 10.31897/PMI.2022.100
28. Vibroacoustic mill charge analyzer VAZM-1M. Available at: http://www.scma.ru/ru/products/2-444.html
29. Demin A. V., Sokolov I. V., Khaymovskiy S. S. Soyuztsvetmetavtomatika process automation solutions for cement industry. TsementInform. 2020. No. 2. pp. 6, 7.
30. Sokolov I. V., Kuzyakov A. V. On the problem of control over the primary grinding mill ball charging. Tsvetnye Metally. 2021. No. 3. pp. 17–22.
31. Damba-Ochir D., Kimyaev I. T., Ulitenko K. Ya. The concept behind a grinding control system built on the basis of vibroacoustic mill charge analyzer VAZM-1M. Tsvetnye Metally. 2003. No. 10. pp. 112–115.
32. Yalin Wang, Xiaofang Chen, Weihua Gui, Chunhua Yang et al. A hybrid multiobjective differential evolution algorithm and its application to the optimization of grinding and classification. Mathematical Approaches in Advanced Control Theories. 2013. Vol. 2013. DOI: 10.1155/2013/841780
33. Tie Qiang Sun, Cui Xue Xie, Zhi Qi Qiu. Iron ore grinding energy conservation research based on neural network. Applied Mechanics and Materials. 2013. Vol. 385–386. pp. 1722–1725. DOI: 10.4028/www.scientific.net/AMM.385-386.1722
34. Yehorov V. System analysis of the technological processes stability. Revista Româna de Informatica si Automatica. 2019. Vol. 29, Iss. 2. pp. 49–62.
35. Tuz A. A., Sanaeva G. N., Prorokov A. E., Bogatikov V. N. Grinding process control and key automation areas. Naukovedenie. 2016. Vol. 8, No. 2. DOI: 10.15862/92TVN216

Full content The practice of using VAZM-1M analyzer in monitoring and control systems designed for tube mills and mill/cyclone stages
Back