Journals →  Chernye Metally →  2023 →  #4 →  Back

5 years of Almalyk branch of NUST MISiS (Uzbekistan)
ArticleName Single-layer hardfacing of excavator bucket teeth
DOI 10.17580/chm.2023.04.06
ArticleAuthor E. S. Nabiev, S. K. Kakhkharov
ArticleAuthorData

Almalyk branch of the National University of Science and Technology "MISiS", Almalyk, Republic of Uzbekistan:

E. S. Nabiev, Cand. Eng., Associate Prof., Dept. of Metallurgy, e-mail: nes.2406@mail.ru
S. K. Kakhkharov, Cand. Eng., Associate Prof., Head of the Mining Dept.

Abstract

To extend the life of excavator bucket teeth, a method of multi-electrode surfacing over a layer of alloy charge is considered: a layer of a special wear-resistant high-carbon hypereutectic alloy alloyed with chromium and manganese is applied to the surface of a worn tooth in one pass. The structure of such alloy consists of trigonal type carbides and a tough metal base. The fusion zone of this alloy with 110G13L steel has been studied. It is shown that the selected composition of welding consumables and the optimized mode of surfacing provide a reliable joint of the wearresistant layer with the base metal. A special multi-electrode installation for surfacing excavator teeth was made. The performance of the welded teeth has been tested in real conditions of soil excavation with rock inclusions. Operational tests showed good wear resistance of the hardfacing metal.

keywords Excavator bucket tooth, multi-electrode surfacing, deposited metal, wear-resistant alloy, metal structure, multi-electrode installation
References

1. Singla Sh., Shibe V., Grewal J. S. Сomparative study of hard faced excavator bucket teeth against abrasive wear using MMAW process. International journal of materials science and engineering. 2011. Vol. 2. No. 1–2. pp. 5–8.
2. Lazić V., Sedmak A., Nikolić R., Mutavdžić М., Aleksandrović S., Krstić В., Milosavljević D. Selection of the most appropriate welding technology for hardfacing of bucket teeth. Materiali in tehnologije [Materials and technology]. 2015. Vol. 1. pp. 165–172.
3. Sharma A., Kumar S. Experimental investigation of the wear behaviour of excavator bucket teeth by hardfacing technique. International Journal of Trend in Scientific Research and Development (IJTSRD). 2019. Vol. 3. Iss. 6. pp. 1239–1243.
4. Kudaybergenov М. S., Mukhamedova N. B., Mirkholikov S. М., Yusubzhonov S. S. Increase of workability of excavator bucket teeth. Eurasian Journal of Academic Research. 2022. Vol. 2, Iss. 13. pp. 242–245.
5. Golikov N. I., Saraev Yu. N., Tikhonov R. P., Semenov S. V., Stepanova К. V., Kharbin N. N. A method for restoring parts of mining equipment operating in the conditions of the North. Nauka i obrazovanie. 2017. No. 4. pp. 82–87.
6. Leonov А. G., Kharitonov V. N., Kovalerov G. I., Serikhin Е. I., Timofeev V. S. Mechanized cladding of excavator bucket teeth with flux-cored strip with an open arc. Svarochnoe proizvodstvo. 1976. No. 9. p. 41.
7. Melikov V. V., Brodyanskiy М. О., Sheynman Е. L., Yakimov А. V., Sokolovskiy B. I. Improvement of the wear resistance of the EKG-4.6 excavator bucket teeth. Gornyi Zhurnal. 1977. No. 12. pp. 47, 48.
8. Burakov А. А., Vulik Yu. А. The use of induction hardfacing to improve wear resistance during abrasive impact wear. Intensification of technological processes of casting, hardening and heat treatment in agricultural engineering. Rostov-na-Donu. 1976. pp. 130–132.
9. Mukashenko А. V. Development of a hardfacing alloy and technology for hardening the teeth of pit excavator buckets. Dissertation … of Candidate of Engineering Sciences. Kursk : Kursk State Technical University, 2008. 132 p.
10. Teplyashin М. V., Komkov V. G., Starienko V. А. Theoretical studies of methods for restoring working bodies using electroslag technology. Elektronnoe nauchnoe izdanie «Uchenye zametki TOGU». 2013. Vol. 4. No. 4. pp. 1537–1542.
11. Melikov V. V., Brodyanskiy М. О., Sheinman Е. L., Yakimov А. V. Wide-layer wear-resistant surfacing of excavators EKG-4,6 buckets teeth. Svarochnoe proizvodstvo. 1977. No. 8. pp. 45, 46.
12. Nabiev E. S., Samborskaya N. А. Surfacing of excavator bucket teeth. Nauchno-tekhnicheskiy zhurnal FerPI. 2019. Vol. 23. No. 1. pp. 29–33.
13. Pobegailo P. А., Kritskiy D. Yu., Gilmanshina Т. R. Wear of elements of mining excavators: analysis of the current state of the problem. Gornyi informatsionno-analiticheskiy byulleten. 2021. No. 2. pp. 64–74.
14. Faizibaev Sh. S., Nabiev E. S., Samborskaya N. А. Technology of hardening of machine parts by multi-electrode surfacing. Vestnik Voenno-tekhnicheskogo instituta Natsionalnoy gvardii Respubliki Uzbekistan. 2020. No. 3 (11). pp. 178–181.

Language of full-text russian
Full content Buy
Back