Journals →  Tsvetnye Metally →  2023 →  #3 →  Back

COMPOSITES AND MULTIPURPOSE COATINGS
ArticleName Mechanical properties of specimens made of aluminium powder ASP-30 by selective laser melting
DOI 10.17580/tsm.2023.03.08
ArticleAuthor Binkov I. I., Denezhkin A. O., Kolchanov D. S., Drenin A. A.
ArticleAuthorData

Bauman Moscow State Technical University, Moscow, Russia:
I. I. Binkov, Category 2 Engineer, Centre for Additive Technologies, e-mail: binkovii@bmstu.ru
A. O. Denezhkin, Postgraduate Student at the Department of Laser Technology in Mechanical Engineering
D. S. Kolchanov, Associate Professor at the Department of Laser Technology in Mechanical Engineering, Candidate of Technical Sciences
A. A. Drenin, Senior Lecturer at the Department of Laser Technology in Mechanical Engineering, Candidate of Technical Sciences

Abstract

This paper examines the process of manufacturing specimens out of aluminium alloy ASP-30 (a counterpart to AlSi10Mg) using the process of selective laser melting (SLM) and equipment made in country. The paper gives a brief description of the equipment developed by BMSTU’s MT-12 department in collaboration with the Centre for Additive Technologies (NOTs “TsAT”). The authors looked at the size distribution, as well as chemical composition and morphology of the obtained materials. In order to establish suitable process parameters, three batches of specimens were prepared under various process parameters. The aim behind making the first batch of specimens was to determine the best orientation of the part in relation to the platform. When making the second and the third batches, the goal was to find the most suitable process parameters, such as beam scan speed, laser radiation power, powder layer height. The authors examined the mechanical properties of the synthesized materials, as well as their bulk porosity and subsurface layer, surface roughness, microstructure and fracture surface. A chemical analysis was performed for the microstructure of the sections. Having analysed the findings, the authors were able to draw conclusions about the orientation of the part in relation to the base plate that would allow to obtain optimum mechanical properties, the optimum process parameters, the required energy input, the microstructure and the distribution of elements in it. Thus, it was established that a vertical orientation would be most beneficial; the highest ultimate strength of 360 MPa was achieved at a layer height of 20 μm and a bulk energy of ~78 J/mm3; the bulk porosity was 2.5% and the elongation at break was 1.56%, which correspondsto brittle fracture mode.

keywords Selective laser melting, additive manufacturing, aluminium, ASP-30, porosity, mechanical properties, microstructure, fracture
References

1. Goncharova O. N., Berezhnoy Yu. M., Bessarabov E. N., Kadamov E. A. et al. Additive technologies as a dynamically developing sector. Engineering journal of Don. 2016. No. 4. p. 12.
2. Logacheva A. I., Sentyurina Zh. A., Logachev I. A. Additive technology for manufacturing parts from metals and alloys in the country (review). Physical and Chemical Basis for Developing Materials and Technology. 2015. No. 5. pp. 5–15.
3. Dynin N. V., Ivanova A. O., Khasikov D. V., Oglodkov M. S. Selective laser melting of aluminium alloys (review). Trudy VIAM. 2017. No. 8. pp. 12–23. DOI: 10.18577/2307-6046-2017-0-8-2-2
4. Karavaev A. K., Puchkov Yu. A. Understanding the structure and properties of alloy AlSi10Mg produced by selective laser melting. Herald of the Bauman Moscow State Technical University. Series Mechanical Engineering. 2020. No. 5. pp. 71–85. DOI: 10.18698/0236-3941-2020-5-71-85
5. Noriko Read, Wei Wang, Khamis Essa, Moataz M. Attallah. Selective laser melting of AlSi10Mg alloy: Process optimization and mechanical properties development. Materials & Design (1980–2015). 2015. Vol. 65. pp. 417–424. DOI: 10.1016/j.matdes.2014.09.044
6. Kaufman J. G. (Ed.). Properties of aluminum alloys: tensile creep and fatigue data at high and low temperatures. Materials Park (Ohio); ASM International (Washington (D.C)), 1999. 264 p.
7. Kempena K., Thijs L., Van Humbeeck J., Kruth J. P. Mechanical properties of AlSi10Mg produced by selective laser melting. Physics Procedia. 2012. Vol. 39. pp. 439–446. DOI: 10.1016/j.phpro.2012.10.059
8. Olakanmi E. O. Selective laser sintering/melting (SLS/SLM) of pure Al, Al – Mg, and Al – Si powders: effect of processing conditions and powder properties. Journal of Materials Processing Technology. 2013. Vol. 213. pp. 1387–1405. DOI: 10.1016/j.jmatprotec.2013.03.009
9. GOST 1497–84. Metals. Methods of tension test. Introduced: 1986–01–01.
10. Feodosiev V. I. Strength of materials. Moscow : Izdatelstvo MGTU im. N. E. Bau mana, 1999. 86 p.
11. Simoni F., Huxol A., Villmer F.-J. Improving surface quality in selective laser melting based tool making. Journal of Intelligent Manufacturing. 2021. Vol. 32. pp. 1927–1938. DOI: 10.1007/s10845–021–01744–9
12. Grigoriants A. G., Kolchanov D. S., Drenin A. A., Denezhkin A. O. Understanding the effect of the key SLM process parameters on the porosity of RS-300 aluminium alloy specimens. Izvestiya vysshikh uchebnykh zavedeniy. Mashinostroenie. 2022. No. 8. pp. 55–64. DOI: 10.18698/0536-1044-2022-8-55-64
13. Chegurov M. K., Sorokina S. A. Fundamentals of fracture analysis in specimens made of structural alloys: Learner’s guide. Nizhny Novgorod, 2018. 79 p.

Language of full-text russian
Full content Buy
Back