Journals →  Chernye Metally →  2022 →  #8 →  Back

Production of cast iron
ArticleName Analytical assessment of the behavior of biochar, as an additionally injected fuel, under conditions of blast-furnace smelting
DOI 10.17580/chm.2022.08.01
ArticleAuthor V. N. Titov, A. V. Karpov, R. I. Khopersky
ArticleAuthorData

Novolipetsk Steel Company (NLMK), Lipetsk, Russia:

V. N. Titov, Cand. Eng., Associate Prof., Chief Specialist in Ore-Thermal Processes Optimization, Technology Development Dept.

 

Lipetsk State Technical University, Lipetsk, Russia:
A. V. Karpov, Cand. Eng., Associate Prof., Dept. of Metallurgical Technologies, e-mail: antonkrpv@rambler.ru
R. I. Khopersky, Assistant, Dept. of Chemistry

Abstract

The relevance of the issue of using carbon-neutral types of raw materials in metallurgical production is considered. One of the promising directions is the use of biomass pyrolysis product - biochar, which has a high carbon content and, as a result, a calorific value relative to biomass. A comparative analysis of the main characteristics of biochar and pulverized coal injected fuel (PCI) produced from "T" and "G" coal grades was carried out. Biochar contains less carbon and ash with a higher content of volatile substances compared to PCI. To study the combustion process of biochar in the blast furnace tuyere zone, a study of the kinetics of its combustion in a laboratory installation for the solid fuel combustion was carried out. In order to adapt the obtained biochar combustion kinetics to the conditions of the blast furnace tuyere zone, a similar study was carried out for the considered types of pulverized coal. The results of the experimental study of the combustion kinetics of the studied types of fuel are presented, according to which the fuel combustion process in front of the tuyeres consists of two phases: the first one is accompanied by a high oxygen consumption for the combustion of volatile substances; the second one is characterized by slow afterburning of the carbon residue. The longest burning time of 0.6 g fuel at a temperature of 1200 °C is 762 s for T-grade PCI. Pulverized coal grade “G” and biochar have the similar combustion kinetics, but the latter burns faster: grade “G” pulverized coal burns in 369 s, and biochar in 162 s. The conclusion is made about a higher degree of biochar afterburning in the conditions of the blast furnace tuyere zone in comparison with pulverized coal fuel.

keywords Biomass, biochar, calorific value, combustion kinetics, blast furnace process, carbon footprint, experimental study, degree of combustion
References

1. Babich А., Senk D. Biomass use in steel industry: back to the future? Chernye Metally. 2013. No. 10. pp. 72–84.
2. Abdullah H., Wu Н. Biochar as a fuel: 1. Properties and grindability of biochars produced from the pyrolysis of mallee wood under slow-heating conditions. Energy & Fuels. 2009. Vol. 23. pp. 4174–4181.
3. Sundqvist L., Lagerwall P., Sundelin B., Orre J., Bramming М., Lundgren М. Blast furnace practice with low emission of carbon dioxide. Chernye Metally. 2018. No. 7. pp. 12–19.
4. Buchwalder I., Grospich К. J., Hartig V., Yanz I., Lüngen H. B., Schmöle P. Requirements for residual materials for injection into blast furnaces. Chernye Metally. 2003. No. 6. pp. 25–33.
5. Lyalyuk V. P., Tarakanov А. К., Kassim D. А., Otorvin P. I., Gusev А. А. Influence of the quality of iron ore raw materials and coke on the technical and economic indicators of blast-furnace smelting. Stal. 2018. No. 12. pp. 2–7.
6. Matsuzaki S., Shinotake A., Naito M., Nishimura T., Kunitomo K., Sugiyama T. Development of mathematical model of blast furnace. Nippon Steel Technical Report. 2006. Vol. 94. pp. 87–95.
7. Shvydkiy V. S., Kudelin S. P., Gurin I. А., Noskov V. Yu. Development of an information-simulating system for the pulverized coal injection into tuyeres of a blast furnace. Izvestiya vysshikh uchebnykh zavedeniy. Chernaya metallurgiya. 2019. Vol. 62. No. 12. pp. 979–986.
8. Kornilov B. V., Chayka А. L., Shostak V. Yu., Sokhatskiy А. А., Moskalina А. А., Fomenko А. P. Analytical study of the combustion process of a coal particle in the blast furnace tuyere zone. Ekologiya i promyshlennost. 2018. No. 2. pp. 30–39.
9. Zhang Y., Deshpande R., Huang D., Chaubal P., Zhou C. Q. A methodology for blast furnace hearth inner profile analysis. ASME Journal of Heat Transfer. 2007. Vol. 129. pp. 1729–1731.
10. Filatov S. V., Myasoedov S. V., Titov V. N., Zagaynov S. А., Gileva L. Yu. Improvement of blast-furnace smelting technology using pulverized coal fuel in NLMK's blast furnace shop No. 1. Chernaya metallurgiya. Byulleten nauchno-tekhnicheskoy i ekonomicheskoy informatsii. 2018. No. 7. pp. 33–39.
11. Wu K., Pan W., Xu W., Yin X., Zhang J., Wu W. Research on Utilization Factor of Injected Pulverized Coal into BF at Large PCI Rate. Steel Research International. 2008. Vol. 79. pp. 904–907.
12. Liu Y., Shen Y. Computational fluid dynamics study of biomass combustion in a simulated ironmaking blast furnace: Effect of the particle shape. Energy and Fuels. 2018. Vol. 32, Iss. 4. pp. 4372–4381.
13. Liu Y., Shen Y. Combined experimental and numerical study of charcoal injection in a blast furnace: Effect of biomass pretreatment. Energy and Fuels. 2020. Vol. 34, Iss. 1. pp. 827–841.

Language of full-text russian
Full content Buy
Back