Journals →  Chernye Metally →  2022 →  #6 →  Back

Rolling and other OMD processes
ArticleName Edge drop of GO steel strips at the hot rolling mill 2000 PJSC «NLMK»
DOI 10.17580/chm.2022.06.03
ArticleAuthor S. M. Belskiy, I. I. Shopin, I. P. Mazur, M. A. Dagman
ArticleAuthorData

Lipetsk State Technical University, Lipetsk, Russia:

S. M. Belskiy, Dr. Eng., Professor, Dept. of Metal Forming, e-mail: belsky-55@yandex.ru
I. I. Shopin, Cand. Eng., Associate Professor
I. P. Mazur, Dr. Eng., Professor, Head of the Dept. of Metal Forming
M. A. Dagman, Postgraduate Student

Abstract

One of the quality characteristics of hot-rolled strips is the transverse thickness variation. The transverse thickness difference is defined as the maximum difference between the measured values of the thickness of the strip in its middle, as well as at a distance of 10 to 40 mm from the edge, depending on the standard used. In many ways, the transverse thickness variation determines the manufacturability of subsequent processing, and also affects the breakage during subsequent cold rolling. Moreover, in recent years there has been a trend towards establishing additional requirements for the transverse thickness variation of electrical steel strips, which often leads to an increase in edge trim to meet these requirements; in particular, this refers to the value of the edge drop of the cross-sectional profile, which is defined as the difference in the thickness of the strip between the edge of the strip and 40 mm from the edge. It is known that the contour of the cross-sectional profile of a hot-rolled strip is inherited by a cold-rolled strip, while the value of the transverse thickness difference decreases in proportion to the elongation coefficient. Thus, hot rolling has a significant effect on the transverse thickness variation of the finished cold-rolled strip. The urgency of the issue of edge drop increases due to the tendency to reduce the size of the side trim of steel strips, which directly affects the consumption coefficient, especially for expensive steel grades, which include transformer steel. To minimize the edge drop value, it is necessary to know the causes of its occurrence and rely on an adequate calculation of the shaping of hot-rolled strips. To create a predictive model of edge drop, rolling parameters are taken into account that affect the shape of the active generatrix of the work rolls. In the presented work, an analysis was made of the influence of hot rolling parameters on the edge drop of rolled strips of GO (transformer) steel. The revealed patterns will form the basis of the developed mathematical model.

keywords Hot rolling, strip cross-sectional profile, transverse thickness variation, edge wedging, transformer steel
References

1. Pimenov V. А., Belskiy S. М., Kuznetsovа Е. V., Shkarin А. N. Mathematical model of profile shape identification of hot-rolled strip cross section and distribution of drawings through cold-rolled strip width. Report 1. Proizvodstvo prokata. 2018. No. 1. pp. 11–15.
2. Belskii S. M., Mukhin Yu. A., Mazur S. I., Goncharov A. I. Influence of the cross section of hotrolled steel on the flatness of cold-rolled strip. Steel in Translation. 2013. Vol. 43. No. 5. pp. 313–316.
3. Shinkin V. N. Preliminary straightening of steel strip. Chernye Metally. 2018. No. 5. pp. 34–40.
4. Shinkin V. N. Simple analytical dependence of elastic modulus on high temperatures for some steels and alloys. CIS Iron and Steel Review. 2018. Vol. 15. pp. 32–38.
5. Maksimov E. A., Shatalov R. L. Asymmetric deformation of metal and front flexure of thick sheet in rolling. Part 1. Steel in Translation. 2012. Vol. 42. No. 5. pp. 442–446.
6. Silberschmidt V. V. Mechanics of materials in modern manufacturing methods and processing techniques. Elsevier, 2020. 465 p.
7. Fedorov V. A., Ushakov I. V., Permyakova I. E. Mechanical properties and crystallization of an annealed cobalt-based amorphous alloy. Metally. 2004. No. 3. pp. 108–113.
8. Fedorov V. A., Ushakov I. V. Effect of annealing on the deformation and fracture of metallic glass under local loading. Technical Physics. 2001. Vol. 46, Iss. 6. pp. 673–676.
9. Shinkin V. N. Elastoplastic flexure of round steel beams. 1. Springback coefficient. Steel in Translation. 2018. Vol. 48. No. 3. pp. 149–153.
10. Shinkin V. N. Elastoplastic flexure of round steel beams. 2. Residual stress. Steel in Translation. 2018. Vol. 48. No. 11. pp. 718–723.
11. Cazacu O., Revil-Baudard B. Plasticity of metallic materials: Modeling and applications to forming. Elsevier, 2020. 560 p.
12. Yanlin L., Jianguo C., Lan Q. et al. Effect of strip edge temperature drop of electrical steel on profile and flatness during hot rolling process. Advances in Mechanical Engineering. 2019. Vol. 11, Iss. 4. pp. 1–11.
13. Kozenkov V. M., Belyaev V. V., Chausov D. N. Thin-film polarizers: properties, technologies, basic types. Liquid Crystals and Their Application. 2021. Vol. 21. No. 2. pp. 5–23.
14. Kozenkov V. M., Belyaev V. V., Chausov D. N. Thin-film polarizers based on lyotropic liquid crystals and photoanisotropic materials: properties and technologies. Liquid Crystals and Their Application. 2021. Vol. 21. No. 3. pp. 6–25.
15. Bel’skii S. M., Mukhin Yu. A. Hot strip rolling with local thickening. Steel in Translation. 2009. Vol. 39. No. 5. pp. 420–424.
16. Hu J., Marciniak Z., Duncan J. Mechanics of sheet metal forming. Butterworth-Heinemann, 2002. 211 p.
17. Skorokhodov V. N., Chernov P. P., Mukhin Yu. A., Bel’skij S. M. Mathematical model of process of free spreading during strip rolling. Stal. 2001. No. 3. pp. 38–40.
18. Shatalov R., Genkin A. Sheet mill control in steel strip hot rolling. Journal of Chemical Technology and Metallurgy. 2015. Vol. 50. No. 6. pp. 624–628.
19. Li H., Fu M. Deformation-based processing of materials: Behavior, performance, modeling and control. Elsevier, 2019. 350 p.
20. Balan K. P. Metallurgical failure analysis: Techniques and case studies. Elsevier, 2018. 294 p.
21. Muhin U., Belskij S., Koynov T. Study of the influence between the strength of antibending of working rolls on the widening during hot rolling of thin sheet metal. Frattura ed Integrita Strutturale. 2016. Vol. 10. No. 37. pp. 318–324.
22. Shinkin V. N. Springback coefficient of round steel beam under elastoplastic torsion. CIS Iron and Steel Review. 2018. Vol. 15. pp. 23–27.
23. Shinkin V. N. Direct and inverse non-linear approximation of hardening zone of steel. Chernye Metally. 2019. No. 3. pp. 32–37.
24. Osipova V. V., Kurilov A. D., Galyametdinov Yu. G., Muravsky A. A., Kumar S., Chausov D. N. Optical properties of nematic liquid crystal composites with semiconductor quantum dots. Liquid Crystals and Their Application. 2020. Vol. 20, Iss. 4. pp. 84–92.
25. Chausov D. N., Kurilov A. D., Belyaev V. V. Liquid crystal nanocomposites doped with nanoparticles of rare earth elements. Liquid Crystals and Their Application. 2020. Vol. 20, Iss. 2. pp. 6–22.
26. Ginzburg V. B. Metallurgical design of flat rolled steels. Marcel Dekker, 2005. 726 p.
27. Roberts W. L. Cold rolling of steel. Marcel Dekker, 1978. 799 p.

Language of full-text russian
Full content Buy
Back