Journals →  Tsvetnye Metally →  2025 →  #1 →  Back

METAL PROCESSING
ArticleName The use of high-frequency wave action for technological quality assurance of boring surfaces of products made of corrosion-resistant aluminum alloys
DOI 10.17580/tsm.2025.01.11
ArticleAuthor Maksarov V. V., Minin А. О., Vasilkov D. V.
ArticleAuthorData

Empress Catherine II Saint Petersburg Mining University, Saint Petersburg, Russia

V. V. Maksarov, Dean of the Mechanical Engineering Faculty, Doctor of Technical Sciences, Professor, e-mail: maks78.54@mail.ru
А. О. Minin, Postgraduate Student of the Mechanical Engineering Department, e-mail: minin.97alex@mail.ru

 

Baltic State Technical University “Voenmeh” named after D. F. Ustinov, Saint Petersburg, Russia

D. V. Vasilkov, Professor of the Department of Technology and Manufacturing of Artillery Weapons, Doctor of Technical Sciences, e-mail: vasilkovdv@mail.ru

Abstract

The issue of technological quality assurance of boring surfaces of products made of corrosion-resistant aluminum alloys is considered. A detailed analysis of the negative factors affecting the process of boring holes in aluminum alloy products has been performed. The study was conducted in order to develop a method for boring holes in products made of corrosion-resistant aluminum alloys, which reduces the size and frequency of build-up on the cutting part of the tool. The process of boring holes in products made of corrosion-resistant aluminum alloys using high-frequency wave action and the roughness of the internal surfaces of the products are studied. A method for boring holes in products made of corrosion-resistant aluminum alloys is proposed, in which the direction of the high-frequency wave action is opposite to the direction of chip flow. As a confirmation of the operability of the proposed processing method, an experimental study of the process of boring holes using high-frequency wave action was performed. The achieved results of the work make it possible to assess in more detail the effect of high-frequency wave action on the frequency of build-up forming, its magnitude and, thus, the roughness of the treated surface. The necessary quality parameters of the surface are provided when performing a high-frequency wave action in the direction opposite to the direction of the chip flow vector.

keywords High-frequency wave action, corrosion-resistant aluminum alloys, build-up forming, surface roughness, aluminum alloy processing, hole boring
References

1. Belyaev A. I., Bochvar O. S., Buinov N. N. et al. Metal science of aluminum and its alloys. Мoscow : Metallurgiya, 1983. 280 p.
2. Markov A. I. Ultrasonic cutting of hard-to-process materials. Мoscow : Mashinostroenie, 1968. 365 p.
3. A. A. Voronin, A. I. Markov. Metal cutting method. Author’s certificate, No. 121638. Bulletin No. 15. Applied: 12. 01.1956. Published: 01.01.1959.
4. Kablov E. N. Aluminum alloys in aerospace engineering. Мoscow : Nauka, 2001. 192 p.
5. Bobrov V. F. Fundamentals of metal cutting theory. Мoscow : Mashinostroenie, 1975. 340 p.
6. Vorontsova L. A., Maslov V. V., Peshkov I. B. Aluminum and aluminum alloys in electrical products. Мoscow : Energiya, 1971. 224 p.
7. Bayat M., Amini S., Hadidi M. Effect of ultrasonic-assisted turning on geometrical tolerances in Al 2024-T6. Materials and Manufacturing Processes. 2021. Vol. 36, Iss. 16. pp. 1875–1886.
8. Yu. V. Kholopov. Apparatus for abrasive-free ultrasonic finishing and final turning of complex-profile surfaces. Patent RF, No. 2317187. Applied: 10.01.2006. Published: 20.02.2008.
9. Majer V. V., Varaksina E. I. Sound and ultrasound in educational research : Textbook. Dolgoprudny : Intellekt, 2012. 336 p.
10. Ershov D. Y., Lukyanenko I. N. Vibration amplitude and frequency parameters of technological equipment drives. Smart Innovation, Systems and Technologies. 2020. Vol. 187. pp. 537–548.
11. Granovskiy G. I., Granovskiy V. G. Metal cutting : Textbook. Мoscow : Vysshaya shkola, 1985. 304 p.
12. Myakotnyh A. A., Ivanova P. V., Ivanov S. L. Criteria and technological requirements for creation of a bridge platform to extract peat raw materials for climate-neutral geotechnology. Russian Mining Industry. 2024. No. 4. pp. 116–120. DOI: 10.30686/1609-9192-2024-4-116-120
13. Korogodin A. S., Ivanov S. L. Maintenance and repair of drum mill trunnions of a floating mining equipment complex. Sustainable Development of Mountain Territories. 2023. Vol. 15. No. 3. pp. 760–770. DOI: 10.21177/1998-4502-2023-15-3-760-770
14. Anuriev V. I. Book for a machine builder. Мoscow : Mashinostroenie, 2001. pp. 699–701.
15. Litvinenko V. S., Dvoinikov M. V. Justification of the technological parameters choice for well drilling by rotary steerable systems. Journal of Mining Institute. 2019. Vol. 235. pp. 24–29. DOI: 10.31897/PMI.2019.1.24
16. Yungmeister D. A., Smolenskii M. P., Isaev A. I., Efimov F. A. Designs and parameters of stepping mechanisms for the complex of extraction of minerals scattered on the seabed. Mining informational and analytical bulletin. 2023. No. 11-1. pp. 159–174. DOI: 10.25018/0236_1493_2023_111_0_159
17. Yu. V. Kholopov. Device for lathe work and finish machining of internal surfaces of details using ultrasound (versions). Patent RF, No. 2343064. Applied: 26.03.2007. Published: 10.01.2009.
18. V. A. Nepomnyashchiy, A. V. Kolobkov. A method of combined lathe work and surface plastic deformation. Patent RF, No. 2728994, C1. Applied: 18.02.2020. Published: 03.08.2020.
19. A. G. Palaev, N. A. Palaev. Ultrasonic oscillating system. Patent RF, No. 94488, U1. Applied: 11.01.2010. Published: 27.05.2010.
20. V. V. Maksarov, A. O. Minin, A. E. Efimov. Method for boring holes in products from corrosion-resistant aluminum alloys. Patent RF, No. 2787289. Applied: 14.06.2022. Published: 09.01.2023.
21. Poduraev V. N. Vibration cutting treatment. Мoscow : Mashinostroenie, 1970. 352 p.
22. Khajehzadeh M., Boostanipour O., Amiri S. The influence of ultrasonic elliptical vibration amplitude on cutting tool flank wear. Journal of Engineering Manufacture. 2020. Vol. 234. pp. 1499–1512.
23. Maslov A. R., Skhirtladze A. G. Cutting treatment of difficult-to-process materials : Textbook. Мoscow : Innovatsionnoe mashinostroenie, 2017. 208 p.
24. Zorev N. N. Investigations into elements of cutting process mechanics. Мoscow : MASHGIZ, 1952. 364 p.
25. Lotfi M., Sajjady S. A., Amini S. Wettability analysis of titanium alloy in 3D elliptical ultrasonic assisted turning. International Journal of Lightweight Materials and Manufacture. 2019. Vol. 2, Iss. 3. pp. 235–240. DOI: 10.1016/j.ijlmm.2019.05.001
26. Zhou W. et al. Towards understanding the ploughing friction mechanism in ultrasonic assisted grinding with single grain. International Journal of Mechanical Sciences. 2022. Vol. 222. 107248.
27. Khalimonenko A. D., Shmakova Yu. R., Admakina O. N., Kufaev V. G. High-speed face milling features of deformable aluminum alloys. Tsvetnye Metally. 2024. No. 6. pp. 81–88.
28. Admakin M. A., Khalimonenko A. D., Zakharova V. P., Nguen Van Dao. Machinability of cutting of low-magnetic high-manganese steels. Chernye Metally. 2023. No. 2. pp. 82–87.
29. Maksarov V. V., Minin A. O., Zakharova V. P. Ensuring surface quality in AlMn alloy items during high-frequency wave impact boring. Tsvetnye Metally. 2023. No. 4. pp. 90–95.
30. Arka G. N. et al. Acoustic horn tool assembly design for ultrasonic assisted turning and its effects on performance potential. Materials and Manufacturing Processes. 2022. Vol. 37, Iss. 3. pp. 260–270.
31. Schmitz Ch. Handbook of aluminum recycling. VulkanVerlag, 2006. 454 p.
32. Sun Y. J. et al. Kinematic analysis of the dynamic contact in ultrasoni cassisted cutting based on the moving frame method. Journal of Materials Processing Technology. 2022. Vol. 309. 117756.
33. He Y., Zhou Z., Zou P., Gao X. et al. Study of ultrasonic vibration–assisted thread turning of Inconel 718 superalloy. Advances in Mechanical Engineering. 2019. Vol. 11, Iss. 10. pp. 1–12.
34. Hara K., Fukuda T., Taguchi K., Isobe H. Surface texturing technique based on ultrasonic turning for improving tribological properties. International Journal of Automation Technology. 2022. Vol. 16, Iss. 1. pp. 78–86.
35. Keksin A. I., Filipenko I. A. Oil and gas sector products cold working process. Topical Issues of Rational Use of Natural Resources 2019. 2020. Vol. 1. pp. 400–405.
36. Eliyasberg M. E. Self-oscillation of metal-cutting machines: Theory and practice. Saint Petersburg : Osoboe KB stankostroeniya, 1993. 180 p.

Language of full-text russian
Full content Buy
Back