Journals →  Chernye Metally →  2022 →  #3 →  Back

Rolling and Metal Science
ArticleName Study of the effect of the cross profile of cold rolled strips on the occurrence of flatness defects
DOI 10.17580/chm.2022.03.10
ArticleAuthor D. L. Shalaevsky, K. P. Korepina

Cherepovets State University, Cherepovets, Russia:

Shalaevsky D. L., cand. Eng., Associate Professor, Dept. of Metallurgy, Mechanical Engineering and Technological Equipment, e-mail:
Korepina K. P., Junior Researcher, Dept. of Metallurgy, Mechanical Engineering and Technological Equipment


The paper considers the influence of the profile of cold-rolled steel, obtained on a multi-stand continuous mill, on one of the main factors in the quality of the shape of a steel strip - the flatness index (non-flatness amplitude and type of defect). For this, the existing model of the formation of the steel strip flatness was used, which takes into account the main factors of rolling and makes it possible to determine the shape of the cross section and the amplitude of the flatness defect of finished steel strips. With the help of the mentioned model, the thickness of the cold-rolled strip along the section width is calculated, and its non-flatness is also determined. Using methods of mathematical statistics, the effect of partial reduction in the last stand of the mill and the convexity of the crosssectional profile of the finished strip on flatness indicators has been established, and limitations on the values of these factors have been determined. A cold rolling mode is proposed on a five-stand mill 1700 of PJSC Severstal, which ensures the production of a strip of a high category of flatness, due to the optimal choice of the distribution of partial reductions over the stands. Introduction of the proposed mode, as well as the modes determined using the created flatness assessment methodology, will reduce the level of rejection by flatness defects to 1–1.5% of the current level.

keywords Steel strip, cross profile, rolling mode, strip flatness, partial reduction, 1700 mill

1. Maksimov Е. А., Shatolov R. L., Boskhamdzhiev N. Sh. Production of flat strips during rolling. Moscow: Teplotekhnik. 2008. 336 p.
2. Rashnikov V. F., Prokhorenko P. А., Denisov P. I., Serov Е. V., Noskov V. L. Stands for efficient strip profile and shape control. Proizvodstvo prokata. 2001. No. 8. 34 p.
3. Bel’skii S. M., Mukhin Yu. A., Mazur S. I., Goncharov A. I. Influence of the cross section of hotrolled steel on the flatness of cold-rolled strip. Steel in Translation. 2013. No. 5. pp. 52–55.
4. Belskiy S. М., Pimenov V. А., Shkarin А. N. Assessment of the actual shape of the hot-rolled strip cross-section contour. Part. 1. Geometric parameters. Chernye Metally. 2020. No. 8. pp. 25–28.
5. Belskiy S. М. Parameters of evaluation of shape cross section of hot-rolled steel strips. Message 1. The determination coefficient. Chernye Metally. 2017. No. 10. pp. 65–70.
6. Dong-Cheng Wang, Hong-Min Liu, Jun Liu. Research and development trend of shape control for cold rolling strip. Chinese Journal of Mechanical Engineering. 2017. Vol. 30. pp. 1248–1261.
7. Yang L., Yu Bing-Qiang. Shape detecting and shape control of cold rolling strip. Advanced Materials Research. 2011. Vol. 311–313. pp. 902–905.
8. Song L., Shen M. G., Yang L. P. et al. Shape control dimensionality reduction efficiency inherited regulation method of cold rolling wide strip. Iron and Steel. 2016. Vol. 51. No. 1. pp. 70–75.
9. Garber E. А., Мishnev P. А., Shalaevskiy D. L., Paligin R. B., Mikheeva I. А., Bolobanova N. L. Modeling and reduction of non-flatness of strips during hot rolling at the stage of setting up a wide-strip mill. Proizvodstvo prokata. 2014. No. 3. pp. 7–13.
10. Garber E. А., Mikheeva I. А., Shalaevskiy D. L., Мishnev P. А., Kukhtin S. A. Development and testing of new methods for improving the flatness of hot-rolled steel wide strips. Chernaya metallurgiya. Byulleten nauchno-tekhnicheskoy i ekonomicheskoy informatsii. 2017. No. 3. pp. 76–83.
11. Budakva А. А., Konovalov Yu. V., Tkalich К. N. et al. Roll profiling of sheet mills. Kiev: Tekhnika. 1986. 189 p.
12. Garber E. А. Cold rolling mills: theory, equipment, technology. Cherepovets: GOU VPO «Cherepovetskiy gosudarstvenny universitet», 2004. 412 p.
13. Korolev А. А. Mechanical equipment of rolling and pipe shops: textbook for universities. 4th edition, revised and enlarged. Moscow: Metallurgiya. 1987. 480 p.
14. Shatalov R., Lukash A. S., Zaikin A. M., Zholobov S. P., Agafonov A. A. Investigation and computer design of the technological modes of continuous rolling of thin brass strips with specified accuracy. Metallurgist. 2018. Vol. 61. No. 11–12. pp. 994–1000.
15. Maksimov E. A., Shatalov R. L., Litvinova N. N. Study of the tractive forces applied to galvanized strip on a straightening machine in a continuous hot-galvanizing unit. Metallurgist. 2014. Vol. 58. No. 5–6. pp. 415–420.
16. Maksimov E. A., Shatalov R. L. Asymmetric deformation of metal and front flexure of thick sheet in rolling. P. 2. Steel in Translation. 2012. Vol. 42. No. 6. pp. 521–525.
17. Maksimov E. A., Shatalov R. L. Asymmetric deformation of metal and front flexure of thick sheet in rolling. P. 1. Steel in Translation. 2012. Vol. 42. No. 5. pp. 442–446.
18. Maksimov E. A., Shatalov R. L. Development of centering guide for quality improvement of steel heavy plates in a roller straightening machine. Chernye Metally. 2018. No. 2. pp. 48–52.

Language of full-text russian
Full content Buy