Журналы →  Tsvetnye Metally →  2022 →  №1 →  Назад

Название Production of aluminum alloy onboard wire with a high content of rare-earth metals produced using electromagnetic crystallization
DOI 10.17580/tsm.2022.01.09
Автор Timofeev V. N., Usynina G. P., Lebedev V. N., Konkevich V. Yu.
Информация об авторе

Research and Production Center for Magnetohydrodynamics Ltd., Krasnoyarsk, Russia1 ; Siberian Federal University, Krasnoyarsk, Russia2:

V. N. Timofeev, Director1, Head of the Сhair for Electrical Technologies and Electrical Engineering2, Doctor of Technical Sciences


Research and Production Center for Magnetohydrodynamics Ltd., Krasnoyarsk, Russia:
G. P. Usynina, Chief Materials Scientist1, Candidate of Technical Sciences, e-mail: galina@usynina.ru


JSC Special Design Bureau of the Cable Industry, Moscow, Russia:
V. N. Lebedev, Deputy General Director for Research


Moscow Aviation Institute (National Research University), Moscow, Russia:
V. Yu. Konkevich, Professor, Chair for Technologies and Systems for Automatic Design of Metallurgical Processes, Doctor of Technical Sciences


The Scientific and Production Center for Magnetic Hydrodynamics Ltd has developed an innovative technology for casting long ingots of small diameter (8–12 mm) into an electromagnetic mold (EMM) and manufacturing thin wire (0.5 mm in diameter) from them for onboard wires from 01417 alloy. Crystallization of liquid metal occurs under the influence of electromagnetic forces in an electromagnetic mold with direct supply of coolant to the ingot, due to which cooling rates are achieved that ensure the dispersion of the eutectic phases of rare earth metal aluminides, similarly to how it takes place during the crystallization of granules (~1.103...1.104 K/s). It has been established that the determining parameters in casting ingots are the power supplied to the inductor and the level of the melt above the crystallization front. For the casting to reach a steady state (the process of stabilizing the diameter of the ingot after the start of casting), it is necessary to regulate the melt level for some time. The surface quality of the ingot depends on ensuring stability of the current in the inductor during casting. Fluctuations in the current in the inductor lead to changes in the ingot`s diameter. Casting speed and metal temperature have a great influence on the structure of ingots. In contrast to the method of producing granulated wire with a thin (less than 1 mm) cross-section, which turned out to be problematic due to numerous breaks during drawing associated with the presence of oxide and foreign inclusions, the casting technology in the electromagnetic mold does not require preliminary metal filtration, since oxide and solid non-metallic inclusions are intensively squeezed out by electromagnetic forces onto the ingot`s surface. It has been established that hot deformation of a billet cast in the EMM at the Conform facility provides higher strength characteristics of the wire from the 01417 alloy after drawing compared to the cast annealed billet. Pressing provided an increase in the yield strength and relative elongation of the 01417 alloy by 2 and 2.5 times, respectively, compared with the cast state. As a result, the billet was obtained with high technological plasticity for further drawing. Electron microscopic studies of the wire have been carried out, which have shown that dispersed REM aluminides are rather uniformly distributed over the cross section of the wire with a diameter of 0.5 mm. Determination of the particle size of aluminides at ×50000 magnification showed that their size is ~96–214 nm. Wire from 01417 alloy is used by JSC “Special Design Bureau of the Cable Industry” (JSC “OKB KP”) for the manufacture of conductive cores of installation wires, providing a significant reduction in their weight.

Ключевые слова Electromagnetic crystallization, magnetohydrodynamic action, high-frequency electromagnetic field, aluminum alloys with rare-earth metals, granular technology, structure dispersion, onboard wires
Библиографический список

1. Dobatkin V. I., Elagin V. I. Granular aluminum alloys. Moscow : Metallurgiya, 1983. 176 p.
2. Azamatov R. А., Aleksandrov V. К., Andreev А. D. et. al. Metallurgy of light alloys. Edited by A. F. Belov. Moscow : Metallurgiya, 1983. pp. 155–160.
3. Ponomarev Yu. I., Fedorov V. М. Development of technology for melting and casting alloy granules. Edited by А. F. Belov. Iss. 2. Moscow : Vserossiyskiy institut legkikh splavov. 1984. pp. 100–105.
4. Usynina G. P. Study of the regularities of the corrosion-electrochemical behavior of aluminum alloys obtained with high cooling rates during crystallization, depending on the structural state of the material and its chemical composition: thesis of inauguaration of Dissertation … of Candidate of Engineering Sciences. Moscow : Vserossiyskiy institut legkikh splavov. 1989. 29 p.
5. Pervukhin M. V., Timofeev V. N., Usynina G. P., Sergeev N. V., Motkov M. M. et al. Mathematical modeling of MHD processes in the casting of aluminum alloys in electromagnetic mold. IOP Conference Series: Materials Science and Engineering. 2019. No. 643. pp. 1–7.
6. Timofeev V. N., Pervukhin M. V., Sergeev N. V. et. al. Metod for continuous casting of an in got and a melting and casting installation for its implementation. Patent 2745520 RF. Published: 23.03.2020.
7. Pervukhin М. V., Timofeev V. N. Modern electrical technologies for production of high-quality aluminum alloys. Krasnoyarsk : Sibirskiy federalny universitet, 2015. 156 p.
8. Getselev Z. N., Balakhontsev G. L., Kvasov F. I., Cherenok G. V., Varga I. I. et. al. Continuous casting in electromagnetic mold. Moscow : Metallurgiya, 1983. 152 p.
9. Masahiro Tani, Masafumi Zeze, Takehiko Toh, Keiji Tsunenari, Kenji Umetsu at el. Electromagnetic casting technique for slab casting. Nipponsteel technical report. 2013. No. 104. pp. 56–61.
10. Evans J. W. The use of electromagnetic casting for Al alloys and other metals. Journal of the Minerals, Metals, and Materials Society. 1995. Vol. 47, Iss. 5. pp. 38–41.
11. Hai Hao, Xingguo Zhang, Shan Yao. Improvement of casting speed and billet quality of direct chill cast aluminum wrought alloy with combination of slit mold and electromagnetic coil. Materials Transactions. 2007. Vol. 48, No. 8. pp. 2194–2201.
12. Official website RPC MAGNETIC HYDRODYNAMICS URL: http://elmacast.com/ (Accessed: 27.01.2022).
13. GOST 10446–80. Wire. Tensile test method. Introduced: 01.07.1982. Moscow : Izdatelstvo standartov, 1980.
14. GOST 7229–76. Cables, wires and cords. Method of measuring of electric resistance of conductors. Introduced: 01.01.1978. Moscow : Izdatelstvo standartov, 1976.
15. Avdulov А. А., Usynina G. P., Sergeev N. V., Gudkov I. S. Distinctive features of the structure and characteristics of long-length light gauge ingots from aluminium alloys, cast into electromagnetic crystallizer. Tsvetnye Metally. 2017. No. 7. pp. 73–77. DOI: 10.17580/tsm. 2017.07.12.

Language of full-text русский
Полный текст статьи Получить