Журналы →  Tsvetnye Metally →  2021 →  №3 →  Назад

65-th anniversary of Soyuztsvetmetavtomatika JSC
Название Application of control units VAZM-2U in ore grinding
DOI 10.17580/tsm.2021.03.02
Автор Kuzyakov A. V., Zhidovetskiy V. D.
Информация об авторе

Soyuztsvetmetavtomatika JSC, Moscow, Russia:

A. V. Kuzyakov, Senior Researcher, Phone: +7 (499) 489-45-96


Kola MMC JSC, Monchegorsk, Russia:
V. D. Zhidovetskiy, Principal Specialist, Automation Office, Candidate of Technical Sciences, Phone: +7 (81536) 7-98-07


This paper considers the results of research work aimed at developing control systems to control ore grinding processes that would be compatible with the control unit VAZM-2U developed by Soyuztsvetmetavtomatika. The underlying principle concerning the unit is that grinding of ores with different mineralogical compositions is governed by the same common regularities in correlation between the physical processes that develop in grinding circuits and the defining process parameters. A grinding mill is fed with ore that has varying physical and mechanical properties, and this can lead to accumulation of material in the mill. Indicators of the probable overload condition include mill vibration level and active power draw of the mill drive motor. The point at which the overload condition has arrived is determined by analyzing active power draw and reverse vibration trends. It is demonstrated that a mill overload condition may take place in those time intervals when both the vibration level and the active power draw of the mill motor fall. In this case the VAZM-2U unit calculates a correction command for the ore flow rate regulator, and this way the overload condition is overcome while the ore feed rate returns to the initial value. The VAZM-2U unit can also help reach the maximum output of the overflow product from a spiral classifier avoiding overgrinding, with the finest material being monitored. The unit can also determine the underflow flow rate in the spiral classifier while adjusting this parameter within a given range of allowable values. The underflow flow rate is estimated with the help of an adaptive mathematical model, which can be utilized in closed-loop grinding circuits that include classifiers. The ore grinding control algorithms implemented in the VAZM-2U unit can be modified to be applicable for milling and flotation control.

Ключевые слова Mill, classifier, grinding, underflow, adjustment, model, overload, vibration, power
Библиографический список

1. Louw D. G., Hulbert V. C., Smith А., Singh G. C. et al. Intek`s process control tools for milling and flotation control. Proceedings of the ХХII International Mineral Processing Congress. Cape Town, South Africa, 14–29 September 2003. Vol. 1. pp. 201–216.
2. Malyarov P. V., Kovalev P. A., Bochkarev A. V., Dolgov A. M. Investigation of mechanisms behind mineral raw materials destruction in ball mills. Obogashchenie Rud. 2018. No. 3. pp. 3–8.
3. Ulitenko K. Ya., Popov V. P. Automatic protection of tumbling mills from overload. Obogashchenie Rud. 2004. No. 2. pp. 38–39.
4. Ulitenko K. Ya., Sokolov I. V., Markin R. P. Noise and vibration analysis used to control volumetric mill charge. Tsvetnye Metally. 2005. No. 10. pp. 63–66.
5. Sokolov I. V., Shapirovskiy M. R., Kuzyakov A. V. Experience of technological processes optimal control (milling complexes) automated systems creation. Tsvetnye Metally. 2015. No. 9. pp. 53–57. DOI: 10.17580/tsm.2015.09.08.
6. Methods of the classical and contemporary theory of automatic control. A textbook in 5 books. 2nd revised edition. Book 5: Methods of the contemporary theory of automatic control. Ed. by K. A. Pupkov, N. D. Egupov. Moscow : Izdatelstvo MGTU im. N. E. Baumana, 2004. 784 p.
7. Sokolov S. V., Kovalev S. M., Smirnov Yu. A., Kucherenko P. Identification methods applicable to fuzzy and stochastic systems. Moscow : Fizmatlit, 2018. 427 p.
8. Methods of the classical and contemporary theory of automatic control. A textbook in 5 books. 2nd revised edition. Book 2: Statistical dynamics and identification of automatic control systems. Ed. by K. A. Pupkov, N. D. Egupov. Moscow : Izdatelstvo MGTU im. N. E. Baumana, 2004. 640 p.
9. Zhidovetskiy V. D., Kuzyakov A. V. Automatic control system for optimum control over converter matte grinding process: development and implementation. Tsvetnye Metally. No. 4. 2020. pp. 13–18.
10. Topchaev V. P., Topchaev A. V., Lapidus M. V. Industrial in-line automatic granulometer PIK-074P as the basis of automatic control and quality materials grinding control systems. Tsvetnye Metally. 2015. No. 9. pp. 48–52.
11. Ulitenko K. Ya., Markin R. P. Grinding mill circulating load determined with the help of process control systems. Obogashchenie Rud. 2005. No. 2. pp. 42–46.
12. Salikhov Z. G., Arunyants G. G., Rutkovskiy A. L. Systems for optimum control over complex production facilities. Moscow : Teploenergetik, 2004. 496 p.
13. Chadeev V. M., Aristova N. I. Control of industrial automation. Tenth International Conference Management of Large-Scale System Development (MLSD). 2017. DOI: 10.1109/MLSD.2017.8109604.
14. Buturuga A., Stoichescu D., Constantinescu R. Universal system for automation of small tasks. International Symposium on Fundamentals of Electrical Engineering (ISFEE). Conference Paper. 2016. DOI: 10.1109/ISFEE.2016.7803157.
15. Fang Yu, Weijin Zhuang, Mingyang Sun. Research and application of operating monitoring and evaluation for dispatching automation and control system. IEEE Advanced Information Management, Communicates, Electronic and Automation Control Conference (IMCEC). Conference Paper. 2016. DOI: 10.1109/IMCEC.2016.7867495.

Language of full-text русский
Полный текст статьи Получить