Журналы →  Non-ferrous Мetals →  2020 →  №1 →  Назад

MATERIALS SCIENCE
Название Alloying-dependent microstructure influence on corrosion resistance of AISI 321 cell joints brazed by Ni-based filler metals
DOI 10.17580/nfm.2020.01.07
Автор Penyaz M., Popov N., Ivannikov A., Sevryukov O.
Информация об авторе

National Research Nuclear University “MEPhI”, Moscow, Russia:

M. A. Penyaz, Post-Graduate Student, Department No. 9 “Physical problems of materials science”, e-mail: mapenyaz@mephi.ru
N. S. Popov, Masters Student, Department No. 9 “Physical problems of materials science”, e-mail: NSPopov@mephi.ru
A. A. Ivannikov, Senior Lecturer, Department No. 9 “Physical problems of materials science”, e-mail: ivannikov7@rambler.ru
O. N. Sevryukov, Associate Professor, Department No. 9 “Physical problems of materials science”, e-mail: sevr54@mail.ru

Реферат

Cellular structures that are widely used as filters and heat exchangers usually operate under high loads and aggressive environments. Corrosion attack can lead to the destruction of the most vulnerable elements of the structure and, as a result, to the failure of the device. This study is devoted to the influence of the elemental composition of nickel-based brazing alloys on the corrosion resistance of brazed joints. Nickel-based brazing alloys based on Ni – Cr – Si – B (BNi-2, BNi-5a) and Ni – Cr – P (BNi-7) systems, and experimental compositions, were selected for the study. The brazing modes were selected according to differential thermal analysis (DTA). The microstructure of the joints was studied using energy-dispersive Х-ray spectroscopy (EDS) on a scanning electron microscope (SEM). The effect of brazing temperature and holding time on grain size and corrosion resistance were evaluated. Corrosion tests were performed in a boiling mixture of CuSO4 and H2SO4 solutions for 8 hours. The obtained microstructures of the brazed joints with different filler metals and different braze modes, before and after corrosion tests, were compared. The erosion activity of brazing alloys was evaluated, and it was found that an increase in the amount of chromium reduces the damages caused by erosion. The relationships between the chemical composition of the filler metals and the brazed joint, the structural-phase state of the joint and the level of corrosion damage are revealed. The influence of elements such as boron, silicon, molybdenum, phosphorous and chromium on the corrosion resistance of the brazed joint is shown. It was found that BNi-5a, BNi-7 and FM04 show the best corrosion resistance. In brazed joints obtained with low-chromium filler metals, a strong dissolution of the zone adjacent to the base material was detected. The purpose of the study is to determine the influence of elements often used in brazing alloys, as well as the structural-phase state, on the corrosion resistance of the brazed joint.
The reported study was funded by RFBR according to the research project №19-32-90092.

Ключевые слова Nickel based filler metal, transient liquid phase bonding, TLP-bonding, brazing, microstructure, fillet, austenitic steel, grain growth, temperature characteristic, corrosion test
Библиографический список

1. MacDonald W. D., Eagar T. W. Transient Liquid Phase Bonding. Annual Review of Materials Science. 1992. Vol. 22, Iss. 1. pp. 23–46.
2. Way M., Willingham J., Goodall R. Brazing Filler Metals. International Materials Reviews. 2019. Vol. 65, Iss. 5.
P. 257–285.
3. Corbin S. F., Murray D. C., Bouthillier A. Analysis of Diffusional Solidification in a Wide-Gap Brazing Powder Mixture Using Differential Scanning Calorimetry. Metallurgical and Materials Transactions: A. 2016. Vol 47, Iss. 12. pp. 6339–6352.
4. Lugscheider E., Partz K.-D. High Temperature Brazing of Stainless Steel with Nickel-Base Filler Metals BNi-2 BNi-5 BNi-7. Welding Journal. 1983. Vol. 62, Iss. 6. pp. 160s–164s.
5. Hartmann T., Marsilius M. Influence of Boron and Phosphor Containing Nickel Based Brazing Alloy on Different Base Materials. LÖT 2016: 11th International Conference on Brazing, High Temperature Brazing and Diffusion Bonding, June 7th to 9th, 2016, Aachen, Germany. 2016. DVS-Berichte, Bd. 325. pp. 227–232.
6. Arafin M. A., Medraj M., Turner D. P., Bocher P. Effect of Alloying Elements on the Isothermal Solidification During TLP Bonding of SS 410 and SS 321 Using a BNi-2 Interlayer. Materials Chemistry and Physics. 2007. Vol. 106, Iss. 1. pp. 109–119.

7. Idowu O. A., Richards N. L., Chaturvedi M. C. Effect of Bonding Temperature on Isothermal Solidification Rate During Transient Liquid Phase Bonding of Inconel 738LC Superalloy. Materials Science and Engineering: A. 2005. Vol. 397, Iss. 1-2. pp. 98–112.
8. State Standart 5639–82 (GOST 5639–82). Steels and alloys. Methods for detection and determination of grain size. Russia, 1983.
9. State Standart 6032–“2003 (GOST 6032–2003), Russia, 2005: Corrosion-resistant steels and alloys. Test methods of intercrystalline corrosion resistance.
10. Cook G. O., Sorensen C. D. Overview of Transient Liquid Phase and Partial Transient Liquid Phase Bonding. Journal of Materials Science. 2011. Vol. 46, Iss. 16. pp. 5305–5323.
11. Jiang W., Gong J. M., Tu S. T. Effect of Holding Time on Vacuum Brazing for a Stainless Steel Plate-Fin Structure. Materials & Design. 2010. Vol. 31, Iss. 4. pp. 2157–2162.
12. Lee Y. W., Kim J. H. Influence of Brazing Temperature on Strength and Structure of SUS304 Stainless Steel Brazed System with BNi-2 Filler Metal: Fundamental Study on Brazeability with Ni-Based Filler Metal(II). Korean Journal of Materials Research. 2007. Vol. 17, Iss. 3. pp. 179–183.
13. Ivannikov A. A., Tukhbatov V. A., Suchkov A. N., Ustyuzha ninov A. L., Bogachev I. A. Rapidly Quenched Nickel Based Filler Metal for High Temperature Various Constructive Elements Brazing. Tsvetnye Metally. 2014. No. 12. pp. 27–31.
14. Novikov I. I., Stroganov G. B., Novikov A. I. Metal Science, Heat Treatment and X-ray-graphy. Moscow: MISIS, 1994. 480 p.
15. Stanley J. K., Perrotta A. J. Grain Growth in Austenitic Stainless Steels. Metallography. 1969. Vol. 2, Iss. 4. pp. 349–362.
16. Miyazawa Y., Saito K., Fukikoshi T., Ariga T., Takizawa T. Brazing of Ferritic Stainless Steel and Microstructure at The Brazed Joint. IBSC 2012: Proceedings from the 6th International Brazing and Soldering Conference. 2012 pp. 236–239.
17. Battenbough A. J., Osmanda A. M., Weinstein M., Lee L., Johnson L. Properties of Selected Nickel and Iron Base Brazing Filler Metals. LÖT 2016: 11th International Conference on Brazing, High Temperature Brazing and Diffusion Bonding, June 7th to 9th, 2016, Aachen, Germany. 2016 DVS-Berichte, Bd. 325. pp. 404–410.
18. Han W. P., Wan M., Zhao R., Kang H., Cheng C., Wang C. J. Effect of Post-Bond Heat Treatment on Microstructural Evolution and Mechanical Properties of Brazed Ultrathin-Walled Structure. Materials Science and Engineering: A. 2019. Vol. 742. pp. 680–691.
19. Jiang W., Gong J., Tu S.T. Effect of Brazing Temperature on Tensile Strength and Microstructure for a Stainless Steel Plate-Fin Structure. Materials & Design. 2011. Vol. 32, Iss. 2. pp. 736–742.
20. Wei J., Ye Y., Sun Z., Zou G., Bai H., Wu A., Liu L. The Effects of Borides on the Mechanical Properties of TLPB Repaired Inconel 738 Superalloy. Metallurgical and Materials Transactions: A. 2017. Vol. 48, Iss. 10. pp. 4622–4631.
21. Wielage B., Hoyer. I., Chemnitz D. Hochtemperaturlöten mit Modifizierten Nickelbasisstandardloten. Hart- und Hochtemperaturlöten und Diffusionsschweien. Düseldorf: Verlag fuer Schweissen und Verwandte Verfahren DVS-Verlag, 2007. Bd. 243. pp. 209–214.
22. Logvenchev I. S., Ivannikov A. A., Volkov A. A., Arofikin N. V., Sevryukov O. N., Fedotov V. T., Suchkov A. N., Fedotov I. V., Skrytnyi V. I. The Brazing of Nickel Alloys for Nuclear Reactor with The Using of the Rapidly-Quenched Filler Metals. Inorganic Materials: Applied Research. 2014. Vol. 5, Iss. 3. pp. 263–267.
23. Tillmann W., Walther F., Manka M., Schmiedt A., Wojarski L., Eilers A., Reker D. W. Investigations of the Corrosion Damage Process of the Brazed Koint AISI 304L/BNi-2. Results in Physics. 2019. Vol. 12. P. 1245–1252.
24. Hartmann T., Nuetzel D. Chromium Containing Amorphous Brazing Foils and Their Resistance to Automotive Exhaust Gas Condensate. IBSC 2012: Proceedings from the 5th International Brazing and Soldering Conference. 2012. pp. 394–400.

Полный текст статьи Alloying-dependent microstructure influence on corrosion resistance of AISI 321 cell joints brazed by Ni-based filler metals
Назад