Журналы →  Non-ferrous Мetals →  2017 →  №2 →  Назад

METAL PROCESSING
Название 3D modeling of combined rolling-extrusion of alloying rods of Al – Ti – B
DOI 10.17580/nfm.2017.02.10
Автор Dovzhenko I. N., Dovzhenko N. N., Sidelnikov S. B., Galiev R. I.
Информация об авторе

Siberian Federal University, Krasnoyarsk, Russia:

I. N. Dovzhenko, Assistant Professor, Chair of Metal Forming
N. N. Dovzhenko, Professor, Chair of Metal Forming
S. B. Sidelnikov, Professor, Head of the Chair of Metal Forming
R. I. Galiev, Assistant Professor, Chair of Metal Forming, e-mail: gri1979@mail.ru

E. V. Gladkov took part in this work.

Реферат

Based on the finite element analysis for the combined rolling-extrusion process, the stress-strain state, force on the tool, and the moments on the rolls are calculated as a function of the tool temperature and the rotational speed of the rolls. The calculations are performed for an Al – Ti – B system alloy containing 5% titanium and 1% boron, widely used in the industry for melt modification when casting ingots of aluminum alloys. The authors proposed ligature rods from this alloy to be produced by the method of combined rolling-extruding (CRE), which has significant advantages in comparison with the traditional technologies of continuous casting-rolling and discrete extruding. Therefore, for the design of technology and equipment for combined processing, it is necessary to have preliminary design data on the temperature-velocity conditions and energy-force parameters of the metal deformation process. For 3D modeling in a software package SolidWorks® the model of the combined rolling-extruding process was created, which was imported into the package DEFORMTM. The simulation process of producing a rod diameter of 9.5 mm by installing rolls with diameters of 462 mm and a protrusion stream 394 mm with rolling reduction of 50% drawing ratio during extruding 6.2 at the rotation speed of 9 rpm data obtained by the temperature distribution metal, strain rates, normal contact stresses on the tool and internal stresses in the metal. In addition, graphs of the change in the forces and moments of rolling acting on the rolls are plotted, depending on the rotational speed of the rolls and the required power of the drive motor is calculated. The obtained data were used in the design of new industrial equipment for combined rollingextruding of aluminum alloys and experimental studies, which confirmed the adequacy of the obtained modeling results.

Ключевые слова ligature, rolling-pressing, rolls, tension, speed, temperature, deformation, force
Библиографический список

1. Sidelnikov S. B. Combined and unified methods of pro cessing of non-ferrous metals and alloys: monography. Krasnoyarsk, Мoscow : МАKS Press, 2005. 344 p.
2. Sidelnikov S. B. Peculiarities of structure formation and properties of metal at rapid solidification-deformation and refinement of aluminum alloys: multi-authored monography. Krasnoyarsk : Sibirskiy Federalnyy Universitet, 2015. 180 p.
3. Grischenko N. А. Mechanical properties of aluminum alloys. Krasnoyarsk: Sibirskiy Federalnyy Universitet, 2012. 196 p.
4. Sidelnikov S. B., Voroshilov D. S., Startsev А. А. Kovaleva A. A., Lopatina E. S., Galiev R. I., Zudin N. A. Research of parameters of combined processing for production of alloying rods of Al – Ti – B alloy system. Journal of Siberian Federal University. Engineering & technologies. 2015. No. 5. pp 646–654.
5. Napalkov V. I. Alloying and grain refinement of aluminum and magnesium. Moscow : MISIS, 2002. 376 p.
6. Bondarev B. I. Refinement of deformed aluminum alloys. Moscow : Metallurgy, 1979. 224 p.
7. Beletskiy V. M. Aluminum alloys. Composition, properties, technologies, application. Reference manual. Kiev: COMINTECH, 2005. 365 p.
8. Elagin V. I. Refinement of deformed aluminum alloys with transition metals. Moscow: Metallurgy, 1975. 248 p.
9. Marcantonio J., Mondolfo L. Grain Refinement in Aluminum Alloyed with Titanium and Boron year. Metallurgical Transactions. 1971. Vol. 2, No. 2. pp. 465–471.
10. Wang X., Song J., Vian W., Ma H., Han Q. The interface of TiB2 and Al3Ti in molten aluminum. Metallurgical and Materials Transactions B. 2016. Vol. 47, Iss. 6. pp. 3285– 3290.
11. Wei Z., Gao X., Feng Z. Application of Al-Ti-B wire in the new high strength wear resistant piston materials. Tezhong Zhuzao Ji Youse Hejin/Special Casting and Nonferrous Alloys. 2016, Vol. 36(8). pp. 874–876.

12. Xu-Guang An, Y. Liu, Jin-Wen Ye, Lin-Zhi Wang, Peng-Yue Wang. Grain refining efficiency of SHS Al – Ti – B – C master alloy for pure aluminum and its effect on mechanical properties. Acta Metallurgica Sinica (English Letters). 2016. Vol. 29, Iss. 8. pp. 742–747.
13. Rakhmonov J., Timelli G., Bonollo F. The influence of AlTi5B1 grain refinement and the cooling rate on the formation behaviour of Fe-rich compounds in secondary AlSi8Cu3 alloys. Metallurgia Italiana. 2016. Vol. 108 (6). pp. 109–112.
14. Wang X., Han Q. Grain refinement mechanism of aluminum by AI – Ti – B master alloys, in Light Metals 2016 (ed. E. Williams). John Wiley & Sons, Inc., Hoboken, NJ, USA. 2016.
15. Zhang Z., Wang J., Xia X., Zhao W., Liao B., Hur B. The microstructure and compressive properties of aluminum alloy (A356) foams with different Al – Ti – B additions. Medziagotyra. 2016. Vol. 22, Iss. 3. pp. 337–342.
16. Wang X., Han Q. Grain refinement mechanism of alumi num by Al – Ti – B master alloys. TMS Light Metals, 2016. pp. 189–193.
17. Baranov V. N., Sidelnikov S. B., Bezrukikh A. I., Zenkin E. Y., Research of rolling regimes and mechanical properties of cold-rolled, annealed and welded semi-finished products from experimental alloys of Al–Mg system, economically alloyed by scandium. Tsvetnye Metally. 2017. No. 9. pp. 83–88.

Полный текст статьи 3D modeling of combined rolling-extrusion of alloying rods of Al – Ti – B
Назад