Journals →  Non-ferrous Мetals →  2023 →  #2 →  Back

MATERIALS SCIENCE
ArticleName The influence of mechanical processing of chip waste from cast Al – Si – B4C composites on the structure and properties of consolidated billets
DOI 10.17580/nfm.2023.02.07
ArticleAuthor Aborkin A. V., Prusov E. S., Deev V. B., Bokaryov D. V.
ArticleAuthorData

Vladimir State University named after Alexander and Nikolay Stoletovs, Vladimir, Russia

A. V. Aborkin, Associate Professor, Department of Technology of Mechanical Engineering, e-mail: aborkin@vlsu.ru
E. S. Prusov, Associate Professor, Department of Functional and Constructional Materials Technology, e-mail: eprusov@mail.ru

D. V. Bokaryov, Post-Graduate Student, Department of Technology of Mechanical Engineering, e-mail: bokarev.1998@list.ru

 

Vladimir State University named after Alexander and Nikolay Stoletovs, Vladimir, Russia1 ; Wuhan Textile University, Wuhan, China2 ; National University of Science and Technology “MISiS”, Moscow, Russia3
V. B. Deev*, Professor, Chief Researcher1, School of Mechanical Engineering and Automation2, Professor of Department of Metal Forming3, e-mail: deev.vb@mail.ru

 

*Correspondence author.

Abstract

In order to increase the efficiency of material extraction during recycling of non-compact waste, solid-phase processing methods are currently being developed to reduce energy consumption in the manufacturing of secondary products. This study provides a comparative evaluation of the influence of high-energy ball milling of chip waste from turning ingots of AlSi12 + 10 vol.% B4C aluminum matrix composite on changes in the structure and mechanical properties of consolidated billets compared to compacted unprepared chips and as-cast state. It was found that the samples consolidated from powder are characterized by increased strength properties in comparison with the cast composite and chips pressed composite. Specifically, the yield strength of the powder consolidated specimens increased by ~1.5 and ~2.3 times compared to the cast composite and chips pressed composite, respectively. The hardness of the cast composite was 39.35 ± 3.2 HRB, while the hardness of the samples consolidated from chips and powder was 42.75 ± 1.2 and 71.4 ± 1.5 HRB, correspondingly. The observed mechanical behavior is associated with a reduction in the sizes of the structural constituents of the matrix alloy, fragmentation of the reinforcing particles, a decrease in the porosity fraction, as well as an increase in the uniformity of particles distribution in the volume of the powder-pressed specimen. The results demonstrate the potential of solid-phase methods for processing non-compact waste in the manufacturing of products from metal matrix composites.

This research was funded by the Russian Science Foundation (Project № 21-79-10432, https://rscf.ru/project/21-79-10432/). The study was carried out using the equipment of the interregional multispecialty and interdisciplinary center for the collective usage of promising and competitive technologies in the areas of development and application in industry/mechanical engineering of domestic achievements in the field of nanotechnology (Agreement No. 075-15-2021-692 of August 5, 2021).

keywords Aluminum matrix composites, chip waste, powder metallurgy, recycling, consolidation, structure and properties
References

1. M ortensen A., Llorca J. Metal Matrix Composites. Annual Review of Materials Research. 2010. Vol. 40, Iss. 1. pp. 243–270.
2. Ramnath B. V., Elanchezhian C., Annamalai R. M., Aravind S., Atreya T. S. A., Vignesh V., Subramanian C. Aluminium Metal Matrix Composites – A Review. Reviews on Advanced Materials Science. 2014. Vol. 38, Iss. 1. pp. 55–60.
3. Bains P. S., Sidhu S. S., Payal H. S. Fabrication and Machining of Metal Matrix Composites: A Review. Materials and Manufacturing Processes. 2016. Vol. 31, Iss. 5. pp. 553–573.
4. Bodunrin M. O., Alaneme K. K., Chown L. H. Aluminium Matrix Hybrid Composites: a Review of Reinforcement Philosophies; Mechanical, Corrosion and Tribological Characteristics. Journal of Materials Research and Technology. 2015. Vol. 4, Iss. 4. pp. 434–445.
5. Miracle D. B. Metal Matrix Composites – from Science to Technological Significance. Composites Science and Technology. 2005. Vol. 65, Iss. 15-16. pp. 2526–2540.
6. Mavhungu S. T., Akinlabi E. T., Onitiri M. A., Varachia F. M. Aluminum Matrix Composites for Industrial Use: Advances and Trends. Procedia Manufacturing. 2017. Vol. 7. pp. 178–182.
7. Prusov E. S., Deev V. B., Aborkin A. V., Bokaryov D. V., Kireev A. V. Metallurgical Processes at the Recycling of Aluminum Matrix Composites via Direct Remelting. Metallurgist. 2022. Vol. 66, Iss. 7-8. pp. 989–1000.
8. Klasik A., Sobczak J., Pietrzak K. Changes in Properties of Aluminium Matrix Composite Reinforced with Sic Particles After Multiple Remelting. Materials Research Innovations. 2011. Vol. 15. pp. S249–S252.

9. Fan T., Zhang D., Yang G., Shibayanagi T., Naka M., Sakata T., Mori H. Chemical Reaction of SiCp/Al Composites During Multiple Remelting. Composites Part A: Applied Science and Manufacturing. 2003. Vol. 34, Iss. 3. pp. 291–299.
10. Fan T. X., Yang G. J., Chen J. Q., Zhang D., Shi Z., Shibayanagi T., Naka M. Recycling Mechanism of Discontinuously Reinforced Al Matrix Composites. Materials Science Forum. 2005. Vol. 502. pp. 205–210.
11. Prusov E. S., Deev V. B., Aborkin A. V., Panfilov A. A., Kireev A. V. Formation of the Structure and Phase Composition of Cast Aluminum Matrix Composites during Multiple Remelting. Russian Journal of Non-Ferrous Metals. 2022. Vol. 63, Iss. 6. pp. 624–630.
12. Palimaka P. Thermal Cleaning and Melting of Fine Aluminium Alloy Chips. Archives of Foundry Engineering. 2020. Vol. 20, Iss. 4. pp. 91–96.
13. Wagiman A., Mustapa M., Asmawi R., Shamsudin S., Lajis M., Mutoh Y. A Review on Direct Hot Extrusion Technique in Recycling of Aluminium Chips. International Journal of Advanced Manufacturing Technology. 2020. Vol. 106. pp. 641–653.
14. Pandey A. K., Prajapati N., Nayak K. C., Date P. P. Sustainable Manufacturing Process for Recycling of Aluminum Alloy Waste into Direct Product by High-Pressure Torsion Process. Materials Today: Proceedings. 2019. Vol. 18. pp. 3099–3108.
15. Li X., Baffari D., Reynolds A. P. Friction Stir Consolidation of Aluminum Machining Chips. International Journal of Advanced Manufacturing Technology. 2018. Vol. 94, Iss. 5-8. pp. 2031–2042.
16. Priarone C. P., Ingarao G., Settineri L., Lorenzo D. R. On the Impact of Recycling Strategies on Energy Demand and CO2 Emissions when Manufacturing Al-Based Components. Procedia CIRP. 2016. Vol. 48. pp. 194–199.
17. Petukhov E. N., Zalesnov A. I., Aborkin A. V. Research of Machinability by Turning of Dispersion-Strengthened Aluminum Matrix Composite Materials. Science Intensive Technologies in Mechanical Engineering. 2014. No. 10. pp. 14–19.
18. Zalesnov A. I., Petukhov E. N., Aborkin A. V. Research of the Mechanism and Development of the Wear Model of a Diamond Tool When Turning Aluminum-Matrix Composite Materials. Journal of Friction and Wear. 2017. Vol. 38, Iss. 5. pp. 377–383.
19. Aborkin A. V., Alymov M. I., Sobol’kov A. V., Khor’kov K. S., Babin D. M. Effect of the Thermomechanical Treatment Conditions on the Consolidation, the Structure, and the Mechanical Properties of Bulk Al–Mg–C Nanocomposites. Russian Metallurgy (Metally). 2018. No. 7. pp. 625–632.
20. Deev V. B., Prusov E. S., Ri E. H. Physical Methods of Processing the Melts of Metal Matrix Composites: Current State and Prospects. Russian Journal of Non-Ferrous Metals. 2022. Vol. 63, Iss. 3. pp. 292–304.
21. Ahmad S. N., Hashim J., Ghazali M. I. The Effects of Porosity on Mechanical Properties of Cast Discontinuous Reinforced Metal-Matrix Composite. Journal of Composite Materials. 2005. Vol. 39, Iss. 5. pp. 451–466.
22. Rahman Md. H., Al Rashed H. M. M. Characterization of Silicon Carbide Reinforced Aluminum Matrix Composites. Procedia Engineering. 2014. Vol. 90. pp. 103–109.

Full content The influence of mechanical processing of chip waste from cast Al – Si – B4C composites on the structure and properties of consolidated billets
Back