Journals →  Non-ferrous Мetals →  2023 →  #1 →  Back

COMPOSITES AND MULTIPURPOSE COATINGS
ArticleName Investigation of the influence of the time and deposition rate on the morphology and phase composition of calcium-phosphate coatings on a TiNi substrate
DOI 10.17580/nfm.2023.01.04
ArticleAuthor Marchenko E. S., Baigonakova G. A., Larikov V. A., Dubovikov K. M.
ArticleAuthorData

National Research Tomsk State University, Tomsk, Russia:

E. S. Marchenko, Doctor of Physical and Mathematical Sciences, Associate Professor, Head of the Laboratory of Medical Alloys and Shape Memory Implants, e-mail: 89138641814@mail.ru
G. A. Baigonakova, Candidate of Physical and Mathematical Sciences, Assistant, Senior Researcher, e-mail: gat27@mail.ru
V. A. Larikov, Post-Graduate Student, Research Engineer, e-mail: calibra1995se@gmail.com
K. M. Dubovikov, Post-Graduate Student, Research Engineer, e-mail: kirill_dubovikov@mail.ru

Abstract

In this work, the effect of technological modes of applying coatings based on calcium-phosphate powder on substrates of titanium nickelide alloys was studied. Compacted powders of calcium phosphates were used as targets. The optimal modes of coating deposition were selected and the deposition rates were determined. The structure, morphology, and phase composition of the alloy surfaces were studied by X-ray diffraction analysis and scanning electron microscopy. According to the results of the atomic force microscopy, a significant decrease in surface roughness was found depending on the thickness of the calcium-phosphate layer. When assessing the cytocompatibility of the alloys, a correlation was found between the number of viable mesenchymal stromal cell cultures and the thickness of the Ca – P coating. When the coating thickness increases, the viability coefficient of cell cultures increases either.

The research was carried out at the expense of the grant of the Russian Science Foundation (RSF), No. 19-72-10105, https://rscf.ru/project/19-72-10105/.
The structure was studied using the equipment of the Tomsk Regional Center for Collective Use of National Research Tomsk State University. The Center is supported by the Grant of the Ministry of Science and Higher Education of the Russian Federation, No. 075-15-2021-693 (No. 13.TsKP.21.0012).

keywords Calcium phosphate, TiNi alloy, ion-plasma sputtering, microstructure, biocompatibility
References

1. Barrere F., van Blitterswijk B. C., de Groot K., Layrolle P. Nucleation of Biomimetic Ca – P Coatings on Ti6A14V from a SBFx5 Solution: Influence of Magnesium. Biomaterials. 2002. Vol. 23, Iss. 10. pp. 2211–2220.
2. Liu J., Liu C., Li J., Liu M., Ruan J.-M. Calcium Phosphate Deposition on Surface of Porous and Dense TiNi Alloys in Simulated Body Fluid. Journal of Central South University. 2016. Vol. 23, Iss. 1. pp. 1–9.
3. Chen X., Li Y., Hodgson P., Wen C. Microstructures and Bond Strengths of the Calcium Phosphate Coatings Formed on Titanium from Different Simulated Body Fluids. Materials Science and Engineering: C. 2009. Vol. 29, Iss. 1. pp. 165–171.
4. Sun L., Berndt C. C., Gross K. A., Kucuk A. Material Fundamentals and Clinical Performance of Plasma-Sprayed Hydroxyapatite Coatings: a Review. Journal of Biomedical Materials Research. 2001. Vol. 58, Iss. 5. pp. 570–592.
5. Zhang Q., Leng Y., Xin R. A Comparative Study of Electrochemical Deposition and Biomimetic Deposition of Calcium Phosphate on Porous Titanium. Biomaterials. 2005. Vol. 26, Iss. 16. pp. 2857–2865.
6. Monma H. Electrolytic Depositions of Calcium Phosphates on Substrate. Journal of Materials Science. 1994. Vol. 29, Iss. 4. pp. 949–953.
7. Filiaggi M. J., Coombs N. A., Pilliar R. M. Characterization of the Interface in the Plasma-Sprayed HA Coating/Ti-6Al-4V Implant System. Journal of Biomedical Materials Research. 1991. Vol. 25, Iss. 10. pp. 1211–1229.
8. Hayashi K., Mashima T., Uenoyama K. The Effect of Hydroxyapatite Coating on Bony Ingrowth into Grooved Titanium Implants. Biomaterials. 1999. Vol. 20, Iss. 2. pp. 111–119.
9. Lacefield W. R. Hydroxyapatite Coatings. Annals of the New York Academy of Sciences. 1988. Vol. 523, Iss. 1. pp. 72–80.
10. Boulton L. M., Gregson P. J., Tuke M., Baldwin T. Adhesively Bonded Hydroxyapatite Coating. Materials Letters. 1991. Vol. 12, Iss. 1-2. pp. 1–6.
11. Wei M., Ruys A. J., Milthorpe B. K., Sorrell C. C. Solution Ripening of Hydroxyapatite Nanoparticles: Effects on Electrophoretic Deposition. Journal of Biomedical Materials Research. 1999. Vol. 45, Iss. 1. pp. 11–19.
12. Wei M., Kim H.-M., Kokubo T., Evans J. H. Optimising the Bioactivity of Alkaline-Treated Titanium Alloy. Materials Science and Engineering: C. 2002. Vol. 20, Iss. 1-2. pp. 125–134.
13. Marchenko E., Baigonakova G., Kokorev O., Yasenchuk Y., Vorozhtsov A. Biocompatibility Assessment of Coatings Obtained in Argon and Nitrogen Atmospheres for TiNi Materials. Metals. 2022. Vol. 12, Iss. 10. 1603.
14. Baigonakova G. A., Marchenko E. S., Yasenchuk Yu. F., Kokorev O. V., Vorozhtsov A. B., Kulbakin D. E. Microstructural Characterization, Wettability and Cytocompatibility of Gradient Coatings Synthesized by Gas Nitriding of Three-Layer Ti/Ni/Ti Nanolaminates Magnetron Sputtered on the TiNi Substrate. Surface and Coatings Technology. 2022. Vol. 436. 128291.
15. Dorozhkin S. V. Calcium-Orthophosphate-Based Bioactive Ceramics. Fundamental Biomaterials: Ceramics. 2018. pp. 297–405.

Full content Investigation of the influence of the time and deposition rate on the morphology and phase composition of calcium-phosphate coatings on a TiNi substrate
Back