Название |
Manipulator for feeding a box with liquid solution for repair of cast iron buckets at blast furnace shop of JSC Ural Steel |
Информация об авторе |
National University of Science and Technology “MISiS”, Novotroitsk affiliate (Novotroitsk, Russia):
A. V. Nefedov, Deputy Director, Cand. Ped., Associate Prof., e-mail: cosnovotr@rambler.ru Yu. V. Novikova, Student, e-mail: nfmisis@yandex.ru
National University of Science and Technology “MISiS” (Moscow, Russia): O. N. Chicheneva, Cand. Eng., Associate Prof., e-mail: ch-grafika@mail.ru |
Реферат |
In the course of production at the site of repair of cast iron buckets, an important stage is the time of transportation of the finished solution to the site for servicing cast iron buckets. This process is carried out manually for small-volume containers or with the help of a workshop bridge crane with a significant volume of the finished solution. In both cases, the repair staff is forced to distract from the main process of repairing the iron buckets and monitor the process of preparing and transporting the solution to the site, as a result of which the entire production process slows down. At the same time, an important aspect is the constant employment of the shop bridge crane due to its operations in other areas of the blast furnace shop. The result is a delay in the working process, and, consequently, an increase in the time required for the repair of cast iron buckets. In this regard, it is proposed to mechanize the process of transporting the finished solution by means of a manipulator, with the help of which the feed is made directly to the site for servicing cast iron buckets, which will exclude the use of manual labor and/or the use of a shop bridge crane. A new design of the manipulator for feeding a box with a liquid solution for the repair of cast iron buckets of the blast furnace shop of JSC Ural Steel has been developed, which allows to increase productivity and reduce operating costs. The main elements of the manipulator arm rotation drive are selected: electric motor, gearbox, clutch with brake, etc. Calculations show that as a result of the implementation of the proposed measures, the time required for transporting the solution to the site will be reduced from 40 to 10 minutes, i.e. the time savings for performing this operation will be 0.5 hours. This modernization requires relatively small capital expenditures for the manufacture and installation of new components and equipment, and the cost-effectiveness of design solutions is to reduce production costs. The payback period of the proposed investment project is less than 4 years. |
Библиографический список |
1. Trofimov V. B. Automated expert systems in sintering process control. Stal. 2020. No. 1. pp. 2–7. 2. Schaap B., Coster P., Brockhus S., Pronk H. Automated control of sheet casting process at the Tata Steel Company in Ijmuiden. Chernye Metally. 2019. No. 4. pp. 10–14. 3. Lukichev S. V., Nagovitsyn О. V., Ilin E. А., Rudin R. S. Digital technologies for sustainable engineering in mining – The first step towards a “smart mine”. Gornyi Zhurnal. 2018. No. 7. pp. 86–90. 4. Sorokin О. I., Shokov А. А. Introduction of automated control over mining and transportation. Gornyi Zhurnal. 2017. No. 5. pp. 85–89. 5. Sholomitskii A., Sotnikov A. Position control and alignment of the CCM equipment. Materials Science Forum. 2019. Vol. 946. pp. 644–649. DOI: 10.4028/www.scientific.net/MSF.946.644. 6. Keropyan A., Albul S., Zarapin A. Problem of increasing tractive effort of railway locomotives in conditions of arctic and continental shelf regions. Lecture Notes in Mechanical Engineering. 2020. Vol. 241. pp. 651–658. DOI: 10.1007/978-3-030-22063-1_69. 7. Kobelev O. A., Albul S. V., Kirillova N. L. Research and development of broaching methods on mandrel of large-sized pipe forgings. IOP Conference Series Materials Science and Engineering. 2020. 6 p. DOI: 10.1088/1757-899X/709/4/044104. 8. Busygin A. M. Cabled feeder for underground drilling machines. Mechanical Engineering. 2020. Vol. 241. pp. 231–237. DOI: 10.1007/978-3-030-22041-9_27. 9. Rylnikova М. V., Vladimirov D. Ya., Fedotenko V. S., Esina Е. N. Intelligent systems and technology in open pit coal mining with high overburden benches. Gornyi Zhurnal. 2018. No. 1. pp. 32–37. 10. Trubetskoy К. N., Rylnikova М. V., Vladimirov D. Ya., Pytalev I. А. Provisions and prospects for introduction of robotic geotechnologies in open pit mining. Gornyi Zhurnal. 2017. No. 11. pp. 60–64. 11. Naumova M., Basyrov I., Aliev K. Reengineering of the ore preparation production process in the context of “Almalyk MMC” JSC. MATEC Web of Conferences. 2018. Vol. 224. No. 01030. DOI: 10.1051/matecconf/201822401030. 12. Chichenev N. A. Reengineering of the Slab-Centering Unit of a Roughing Mill Stand. Metallurgist. 2018. Vol. 62. No. 7 – 8. pp. 701–706. 13. Gorbatyuk S. M., Morozova I. G., Naumova M. G. Development of the working model of production reindustrialization of die steel heat treatment. Izvestiya Vysshikh Uchebnykh Zavedeniy. Chernaya Metallurgiya. 2017. Vol. 60, Iss. 5. pp. 410–415. 14. Chichenev N. A. Import-replacing re-engineering of the drive of the rollers in the intermediate roller table of a continuous bloom caster. Metallurgist. 2015. Vol. 58. No. 9–10. pp. 892–895. 15. Gorbatyuk S. M., Zarapin A. Yu., Chichenev N. A. Retrofit of vibrating screen of Catoca mining company (Angola). Gornyi Informatsionno-analiticheskiy Byulleten. 2018. No. 1, pp. 143–149. 16. Vegman E. F., Zherebin B. N., Pokhvisnev A. N. et al. Iron metallurgy. A textbook for high schools. 3rd edition. Мoscow. IKTs “Akademkniga”. 2004. 774 p. 17. Malygin A. V., Maltsev V. A., Viduetskiy M. G. Ore preparing processes in melting production. Ekaterinburg. AMK Den RA. 2016. 415 p. 18. Kurunov I. F. State and tendencies of metallurgy and iron development worldwide meeting the XXI century challenges. Iron metallurgy – XXI century challenges. Proceedings of the VIII International congress of ironmakers. Мoscow: Kodeks. 2017. pp. 10–20. 19. Ural Steel – Metalloinvest. Available at: http://www.metalloinvest.com/business/steel/uralsteel/ (accessed: 09.01.2021). 20. Tselikov А. I., Polukhin P. I., Grebenik V. М. et. al. Machines and units of metallurgical plants. In 3 volumes. Vol. 1. Machines and units of blast furnace shops: Textbook for universities. Moscow: Metallurgiya, 1988. 440 p. 21. Aleksandrov А. P. Hoisting machines: Textbook for universities. Moscow: Izdatelstvo MGTU imeni N. E. Baumana – Vysshaya shkola, 2000. 552 p. 22. Electric motors asynchronous with a squirrel-cage rotor of the AMU112 series. Available at: http://prom-pump.ru/elektrodvigateli/obschepromyshlennye/amu112m8 (accessed: 09.01.2021). 23. Reducer cylindrical worm of 1 TsCh-160 type. JSC Reduktor. Available at: http://www.jscreduktor.ru/cch/1cch-160.html (accessed: 09.01.2021). 24. GOST 21424-93. Flexible couplings with rubber-bushed studs. Parameters and dimensions. Moscow: Standartinform, 2014. 10 p. 25. Flexible coupling with rubber-bushed studs MUVP-5 with a brake pulley D = 200 mm. Kaluga Crane Equipment Plant. Available at http://kzko40.ru/produkt/mufta_muvp_s_tormoznym_shkivom/muvp5_s_tormoznym_shkivom_d-200/ (accessed: 09.01.2021). 26. TKG shoe brakes. Industrial and technical enterprise “Drive Equipment Plant”. Available at: http://reduktor-ptp.ru/old/tormoz-tkg-200/ (accessed: 09.01.2021). |