Journals →  Tsvetnye Metally →  2021 →  #1 →  Back

METAL PROCESSING
ArticleName Understanding the process of making fuse contacts by upsetting of aluminium bars
DOI 10.17580/tsm.2021.01.07
ArticleAuthor Lisunets N. L., Zhigulev G. P., Hoang Man Goyi, Nguyen Truong An
ArticleAuthorData

National University of Science and Technology MISiS, Moscow, Russia:

N. L. Lisunets, Associate Professor at the Department of Metal Forming, Candidate of Technical Sciences, e-mail: lisunec@yandex.ru
G. P. Zhigulev, Senior Researcher, Lead Expert at the Department of Metal Forming, Candidate of Technical Sciences

Hoang Man Goyi, Postgraduate Student at the Department of Metal Forming

 

Le Quy Don Technical University, Hanoi, Vietnam:
Nguyen Truong An, Research Fellow, Candidate of Technical Sciences

Abstract

This paper describes the results of a study that looked at an innovative wastefree process of cold upsetting to make power fuse contacts from the commercial aluminium grade AD1. The process involves upsetting and extrusion of a workpiece cut from steel bar stock in the same die in one process step. It is proposed to use this process instead of making each separate fuse contact part, i.e. when the fuse base and the knife are notched out of a steel bar and are then stamped together. The new process is less labour intensive due to less pieces of die tooling used, less equipment required, less personnel involved and due to a significantly higher metal utilization factor – 1 instead of 0.7. Solid models have been developed for the solid part of fuse contact and for the die tooling so that this process could be performed in a die. A procedure has been developed for making fuse contacts by cutting a steel bar in the die with a flat end punch followed by upsetting and extrusion of the workpiece. The dimensions of the primary blank and the forces acting at different process steps have been determined. The upper-bound method was applied to conduct a theoretical study of kinematic parameters and forces involved in the process. Physical and mathematical modelling helped establish how a steel bar changes its shape under upsetting and extrusion. Having analyzed the block models of the extrusion process with kinematically possible velocity fields, the authors identified what conditions lead to defect formation and offered some measures to prevent such defects. Force-geometry relationships have been defined. Experimental die tooling has been made and a prototype die – designed to implement this process in practice. A pilot batch of fuse contacts has been produced.

keywords Fuse contact, steel bar, upsetting, extrusion, extrusion defect, solid model, die tooling
References

1. Lisunets N. L., Tsepin M. A., Smirnov O. M., Kachalin A. A., Paramonov V. V. Types of primary blanks made of aluminium alloys and selecting processes to make semi-finished and finished parts out of them. Tsvetnye Metally. 2005. No. 1. pp 87–91.
2. GOST 4784–2019. Aluminium and wrought aluminium alloys. Grades. Introduced: 01.09.2019.
3. Forging and stamping: Handbook in 4 volumes. Vol. 3 and 4. Ed. by E. I. Semenov. Moscow : Mashinostroenie, 1985.
4. Lisunets N. L. Usage of physical and mathematical simulation for improvement of the process of metal shear cutting. CIS Iron and Steel Review. 2019. Vol. 17. pp. 34–38.
5. Lisunets N. L., Demetrashvili I. S., Hoang Man Goyi. Development and characterization of the manufacturing process of cylindrical-shaped semi-finished products from non-ferrous alloys for stamping on the basis of modeling. Tsvetnye Metally. 2018. No. 5. pp. 82–85.
6. Lisunets N. L., Hoang Man Goyi. Understanding the process of upsetting in a closed cylindrical die to produce workpieces for cold upsetting. Zagotovitelnye proizvodstva v mashinostroenii. 2018. Vol. 16, No. 6. pp. 258–265.
7. Lampman S. Cold Extrusion of Aluminum Alloy. Aluminum Science and Technology. ASM International. 2018. Vol. 2A. pp. 311–314.
8. Alieva L. I., Zhbankov Ya. G., Grudkina N. S., Abkhari P. B. Defect formation during cold extrusion. Theoretical and practical problems of metal forming and the quality of professional education: Proceedings of the 7th International Science and Technology Conference. Kiev-Kherson : NTUU “KPI”, 2016. pp. 51–53.
9. Dmitriev A. M., Vorontsov A. L. Predicting metal stamping defects. Spravochnik inzhenera. 2004. No. 11. pp. 29–32.
10. Vaysburd R. A., Partii A. S. Understanding how extrusion defects form and predicting the shape of such defect as a result of extrusion into a slit-shaped cavity. Izvestiya vysshikh uchebnykh zavedeniy. Mashinostroenie. 1999. No. 1. pp. 30–34.
11. Johnson W., Mellor P. B. Engineering plasticity. Translated from English by A. G. Ovchinnikova. Moscow : Mashinostroenie, 1979. 567 p.
12. Alyushin Yu. A. Application of the upper-bound method to determine specific pressures and minimal reductions during pressing. Forging and Stamping Production. Material Working by Pressure. 1965. No. 4. pp. 19–24.
13. Solomonov K. N., Tishchuk L. I. Review of software for simulation of metal forming processes. Collective monograph on the XV International Scientific Conference New technologies and achievements in metallurgy, material engineering and production engineering. Czestochowa (Poland). 2014. No. 40. pp. 287–291.
14. Goncharuk K. V., Alieva L. I., Grudkina N. S., Tagan L. V., Shkira A. V. Analyzing the effect of the tool shape on the force distribution during complex upsetting. Science Bulletin of Donbass State Engineering Academy. 2015. No. 3. (18Е). pp. 71–79.

Language of full-text russian
Full content Buy
Back