Журналы →  Non-ferrous Мetals →  2019 →  №2 →  Назад

AUTOMATION
Название Scientific and technical directions of improvement of electric motors for non-ferrous metallurgy
DOI 10.17580/nfm.2019.02.09
Автор Kurilin S. P., Denisov V. N., Dli M. I., Bobkov V. I.
Информация об авторе

Branch of the National Research University “Moscow Power Engineering Institute”, Smolensk, Russia:

S. P. Kurilin, Professor at the Department of Electromechanical Systems, e-mail: sergkurilin@gmail.com
V. N. Denisov, Professor at the Department of Higher Mathematics, e-mail: dvalnik@mail.ru
M. I. Dli, Professor, Head of the Department of Information Technologies in Economics and Management, e-mail: midli@mail.ru
V. I. Bobkov, Associate Professor at the Department of Higher Mathematics, e-mail: vovabobkoff@mail.ru

Реферат

Induction motors of classical and special design modifications are used in electric drives of non-ferrous metallurgy shop equipment. Technical requirements for classic induction motors (IM) include high energy efficiency and a high degree of reliability. The most important are the requirements of high starting torque, low starting current and low dependence of startability upon the mains supply voltage fluctuations. Classic electric motors, both general-purpose and specialized, satisfy the needs of metallurgical industries in terms of starting torque, but they have overestimated values of the locked rotor current ratio by 1.5–2 times. Radical decrease of the locked rotor current ratio presents one of the topical areas of improving the IMs for non-ferrous metallurgy. The design description is given, and technical indicators of the upgraded electric motor with low starting current are pointed out. Linear induction motors (LIM) are considered as a typical example of electric motors of a special design modification. In the aspect of low material capacity, kinematic simplicity and reliability, LIMs compete with classical IM. The widespread introduction of LIMs into electric drives of workshop equipment will significantly reduce material capacity and increase the reliability of non-ferrous metallurgy. The LIM specificity is analyzed. Description of the design and technical parameters of the LIM with a short carriage are given. Regular assessments of the current technical condition of electric motors and the risk of their operability loss are the measure of significant increase in reliability of the electrical equipment of non-ferrous metallurgy. The assessments of performance risks that could be obtained without significant interruptions in exploitation of the equipment are in demand. The article presents a method for topological IM diagnostics. The electric motor diagnostic testing methodology is described, and quantitative measures of the risk of operability loss are introduced.

This study has been carried out done within framework of the basic part of a State task of the Ministry of Education and Science of the Russian Federation to perform public works in the field of scientific activities, project No. 13.9597.2017/БЧ.

Ключевые слова Electrical equipment, reliability, material capacity, induction motors, low starting current, linear electric motors, operational diagnostics, diagnostic testing methodology, the operability loss risk assessments
Библиографический список

1. Kopylov I. P. Electric machines : Manual in 2 volumes. Vol 2. Moscow : Urait, 2017. 407 p.
2. Goldberg O. D., Makarov L. N. Khelemskaya S. P. Engineering design of electric machines. Moscow : BASTET Publishing House, 2016. 528 p.
3. Makarov L. N., Denisov V. N., Kurilin S. P. Upgraded Asynchronous Motors with a Squirrel Cage Rotor. Russian Electrical Engineering. 2019. Vol. 90, Iss. 3. pp. 216–220.
4. Bobkov V. I., Denisov V. N., Dli M. I., Kurilin S. P., Filatenkov A. A. Rotor of induction motor. Patent RF, No. 2690680. Published: 05.06.2019. Bulletin No. 16.
5. Kurilin S. P., Denisov V. N. Topological aspects of the theory of asynchronous electric machines. Smolensk : UNIVERSUM, 2019. 200 p.
6. Panchenko S. V., Meshalkin V. P., Dli M. I., Borisov V. V. Dynamics of Thermophysical Processes in Electrothermal Reducer. Non-ferrous Metals. 2015. No. 2. pp. 56–60. DOI: 10.17580/nfm.2015.02.10.
7. Panchenko S. V., Dli M. I., Bobkov V. I., Panchenko D. S. Certain of the Thermal Physics Problems of Reducing Processes in Chemical Electrothermal Reactors. Non-ferrous Metals. 2017. No. 1. pp. 43–48. DOI: 10.17580/nfm.2017.01.09.
8. Panchenko S. V., Dli M. I., Panchenko D. S., Chernovalova M. V. Thermalphysic processes in a reaction zone of electrothermal ore-smelting reactor. Non-ferrous Metals. 2018. No. 1. pp. 37–42. DOI: 10.17580/nfm.2018.01.07.
9. Thorsen O., Dalva M. Condition Monitoring Methods, Failure Identification and Analysis for High Voltage Motors in Petrochemical Industry. Eighth International Conference on Electrical Machines and Drives, Cambridge, UK, 1–3 Sept. 1997. pp. 109–113.
10. Tarasov V. A., Leisle A. G., Petrochenkov A. B. The Use of a Topological List for Calculating the Parameters of Electric-Power Systems on the Basis of the Node-Voltage Method. Russian Electrical Engineering. 2016. Vol. 87, Iss. 11. pp. 615–619.
11. Zoric I., Jones M., Levi E. Arbitrary Power Sharing Among Three-Phase Winding Sets of Multiphase Machines. IEEE Transactions on Industrial Electronics. 2017. Vol. 65, Iss. 2. pp. 1128–1139.
12. Farhani F., Zaafouri A., Chaari A. Real Time Induction Motor Efficiency Optimization. Journal of the Franklin Institute. 2017. Vol. 354, Iss. 8. pp. 3289–3304.
13. Zheng J., Huang S., Rong F., Lye M. Six-Phase Space Vector PWM Under Stator One-Phase Open-Circuit Fault Condition. Energies. 2018. Vol. 11, Iss. 7. 1796. DOI: 10.3390/en11071796.
14. Kosmatov V. I., Sarvarov A. S., Danilov E. I. Mathematical Model of Energy-Saving Asynchronous Motor in the Rotating Coordinates System. 17th International Ural Conference on AC Electric Drives (ACED). 2018. pp. 1–5.
15. Kurilin S. P., Denisov V. N., Fedulov A. S., Dli M. I. Scientific Basis of Methods for Topological Diagnostics of Asynchronous Electric Machines. AIP Conference Proceedings. 2018. Vol. 2053. 030031. DOI: 10.1063/1.5084392.

Полный текст статьи Scientific and technical directions of improvement of electric motors for non-ferrous metallurgy
Назад