Journals →  Gornyi Zhurnal →  2019 →  #11 →  Back

RAW MATERIAL BASE
ArticleName Garnet from the White Sea coast as a promising abrasive raw material
DOI 10.17580/gzh.2019.11.09
ArticleAuthor Kravchuk K. S., Gladkikh E. V., Useinov A. S., Elenskiy A. Yu.
ArticleAuthorData

Technological Institute of Superhard and Novel Carbon Materials, Troitsk, Russia:

K. S. Kravchuk, Researcher, Candidate of Physico-Mathematical Sciences
E. V. Gladkikh, Trainee Researcher, ekat.gladkih@yandex.ru
A. S. Useinov, Head of Department, Candidate of Physico-Mathematical Sciences

 

TENGRI LLC, Arkhangelsk, Russia:

A. Yu. Elenskiy, Chief Executive Officer

Abstract

Natural garnet is a widespread abrasive raw material. Its wide application range is associated with a number of unique physical and mechanical properties. Garnet sand is actively used in sandblasting and water jet cutting. This work is aimed at comparing physical, mechanical and cutting properties of garnet sand produced in India (imported by R-Garnet) and mined on the coast of the White Sea (TENGRI LLC). The samples of garnet sand chosen for the study had Mesh 80 fraction, the grit size was 150–300 μm. A series of mechanical tests were carried out with the garnet sand. In some tests initial sand was divided into fractions with different color of grit. Nanoindentation tests were carried out to determine the hardness and modulus of elasticity. The static strength was determined in the compression tests. The bulk density, abrasiveness and cuttability were measured. The comparative tests of garnet sand were carried out on a water jet cutting machine. It was shown that the abrasive and cutting properties of the White Sea garnet sand and Indian sand coincide within the error limits. During water jet cutting the penetration rates in metal, as well as the speed and evenness of the cut are the same for both sands. The bulk density value has small differences for both groups of samples. Scanning electron microscope equipped with a spectrometer for energy-dispersive analysis was used for the elemental composition investigation of particles of different color. The particles of garnet sand (red-brown grains) of both deposits have hardness (13±2) GPa and static compressive strength (7.0±0.6) N. Garnet contains a small amount of black and green admixture (less than 10%). Most of the impurity particles correspond to ilmenite and pyroxene. The impurity has a 1.5 times less hardness, and the compressive strength if the impurity is 2 times less than garnet particles have.
The study was supported by the Russian Foundation for Basic Research, Project No. 18–08–00558.

keywords Garnet, tool indentation, hardness, modulus of elasticity, mechanical strength, abrasiveness, cuttability, bulk density
References

1. Dushin A. V., Yurak V. V. Authors’ approach to the Total Economic Value: Essentials, structure, evolution. Eurasian Mining. 2018. No. 1. pp. 11–15. DOI: 10.17580/em.2018.01.03
2. Baranov M. N., Isupov M. G., Isupov G. P. Strength of material in jet-abrasive machining. Russian Engineering Research. 2009. Vol. 29, No. 5. pp. 482–486.
3. Elsner H. Heavy Minerals of Economic Importance. Hannover : Federal Institute for Geosciences and Natural Resources, 2010. 218 p.
4. Sayapina E. S., Sarilov M. Yu. Hydroabrasive cleaning of tank walls for oil storage and transportation. Automation of Mechanical Conversion, Hardening and Assemblage Process Flows in Machine Building : International Scientific-and-Technical Conference Proceedings. Kursk, 2016. pp. 270–273.
5. Brobst D. A., Pratt W. P. United States Mineral Resources : Geological Survey Professional Paper 820. Washington, 1973. 722 p.
6. Industry quality specifications for mineral raw material: Handbook for geologists. 2nd enlarged edition. Moscow : Gosgeoltekhizdat, 1962. Iss. 33. Garnet. 26 p.
7. Hlavacova I. M., Geryk V. Abrasives for water-jet cutting of high-strength and thick hard materials. The International Journal of Advanced Manufacturing Technology. 2017. Vol. 90, Iss. 5–8. pp. 1217–1224.
8. Boud F., Carpenter C., Folkes J., Shipway P. H. Abrasive waterjet cutting of a titanium alloy: The influence of abrasive morphology and mechanical properties on workpiece grit embedment and cut quality. Journal of Materials Processing Technology. 2010. Vol. 210, Iss. 15. pp. 2197–2205.

9. Dewan Hasan Ahmed, Jamal Naser, Rowan Thomas Deam. Particles Impact Characteristics on Cutting Surface During the Abrasive Water Jet Machining : Numerical Study. Journal of Materials Processing Technology. 2016. Vol. 232. pp. 116–130.
10. Aydin G., Kaya S., Karakurt I. Utilization of solid-cutting waste of granite as an alternative abrasive in abrasive waterjet cutting of marble. Journal of Cleaner Production. 2017. Vol. 159. pp. 241–247.
11. Shpilev V. V. Increase waterjet cutting capacity jets. The Potential of Modern Science : International Scientific-and-Practical Conference Proceedings. Praga, 2016. pp. 117–122.
12. Tarasova O. A., Shurygin A. Yu. Material treatment by water jet cutting. Molodezhnyi nauchnyi forum: tekhnicheskie i matematicheskie nauki. 2016. No. 11(40). pp. 170–178.
13. Grew E. S., Locock A. J., Mills S. J., Galuskina I. O., Galuskin E. V., Hålenius U. IMA report: Nomenclature of the garnet supergroup. American Mineralogist. 2013. Vol. 98, No. 4. pp. 785–810.
14. Barsukov G. V., Mikheev A. V. Modelling trend jet waterjet cutting material packaged with interlayer gap on the feed rate of the nozzle and type abrasive. Vestnik nauki i obrazovaniya Severo-Zapada Rossii. 2015. Vol. 1, No. 4. pp. 61–68.
15. Kuzhvart M. Non- metallic mineral resources. Translated from English. Moscow : Mir, 1986. 471 p.
16. Useinov A., Kravchyuk K., Rusakov A., Maslenikov I., Krasnogorov I. Methods of automation of mechanical properties measurements in NanoScan nanohardness testers. Nanoindustry. 2016. No. 7(69). pp. 72–78.
17. GOST R 8.748–2011 (ISO 14577–1:2002). State system for ensuring the uniformity of measurements. Metallic materials. Instrumented indentation test for hardness and materials parameters. Part 1. Test method. Moscow : Standartinform, 2013. 28 p.
18. GOST 9206–80. Diamond powders. Specifications (with changes No. 1, 2, 3). Moscow : Izdatelstvo standartov, 1989. 55 p.
19. GOST 28924–91. Grinding materials. Test methods of physical and physical-mechanical properties (with changes No. 1). Moscow : IPK Izdatelstvo standartov, 2004. 14 p.
20. GOST 25142–82 (ST SEV 1156–78). Surface roughness. Terms and definitions (with changes No. 1). Moscow : Standartinform, 2018. 17 p.
21. GOST 2789–73. Surface roughness. Parameters and characteristics (with changes No. 1, 2). Moscow : Standartinform, 2018. 7 p.
22. Whitney D. L., Broz M., Cook R. F. Hardness, toughness, and modulus of some common metamorphic minerals. American Mineralogist. 2007. Vol. 92, No. 2-3. pp. 281–288.
23. Goldstein J. I., Newbury D. E., Echlin P., Joy D. C., Fiori C., Lifshin E. Scanning Electron Microscopy and X-Ray Microanalysis. New York : Kluwer Academic/Plenum Publishers, 2003. 689 p.
24. Bella M. D., Italiano F., Romano D., Tripodo A., Sabatino G. Geochemistry and tectonic setting of triassic magmatism from the Lercara Basin (Sicily, Italy). Periodico di Mineralogia. 2017. Vol. 86, No. 2. pp. 169–181.

Language of full-text russian
Full content Buy
Back