Journals →  Chernye Metally →  2019 →  #9 →  Back

Rolling and other metal forming processes
ArticleName Application of the saddle coefficient for estimating the quality of a hot-rolled steel strip
ArticleAuthor S. M. Belskiy, I. I. Shopin
ArticleAuthorData

Lipetsk State Technical University (Lipetsk, Russia):

S. M. Belskiy, Dr. Eng, Prof., Metall Forming Dept., e-mail: belsky-55@yandex.ru
I. I. Shopin, Cand. Eng., Metall Forming Dept.

Abstract

Cross-section thickness is the most important characteristic of the quality of hot-rolled steel due to the fact that it largely determines the manufacturability of subsequent processing including breaks during cold rolling of hot rolled strips. Cross-section thickness variation is a set of multiple thickness measurements across the width of a hot rolled strip. Such a set is called a strip cross section profile. Therefore, in order to assess the impact on any quantitative characteristics of manufacturability, a small number of parameters should characterize an array of measurements. For this, the cross section profile is approximated with a parabola, most often of the second order. In the scientific and technical literature, a number of similar characteristics of the cross-sectional profile are indicated: convexity, wedge, thickness variation, displacement, coefficient of determination, and wedge in near-rim zones. Recently, a new characteristic of the cross-section profile, the saddle coefficient, has been introduced into scientific use. The key feature of this characteristic is the amplification effect of deviations from the parabolic approximation of the cross-section profile in the near-rim zones of the strip. The article shows a statistically significant effect on the breakage during cold rolling of the transverse thickness variation of the hot rolled strip. As the characteristics of the transverse thickness variation, the saddle coefficient and wedge in near-rim zones are used. The study was conducted by the method of statistical testing of hypotheses by p-value based on regression modeling. In the mathematical model, the probability of strip breakage during cold rolling of a hot rolled strip without preliminary trimming was estimated. Binary logistic regression is best suited for mathematical modeling of the probability of an event occurring (strip breakage). According to the results of statistical analysis, the significance of the influence of the saddle coefficient and wedge in near-rim zones was confirmed. Revealed a strong nonlinearity of the influence of the parameters of the transverse thickness variation on the probability of strip breakage. The optimal ranges of parameters were determined for the saddle coefficient of shape and wedge in near-rim zones in which the probability of breakage strip during cold rolling is minimal.

keywords Thin sheet hot rolling, thin sheet cold rolling, cross-section profile of strips, the saddle coefficient, wedge in near-rim zones
References

1. Korolev А. А. Mechanical equipment for rolling and pipe shops. Moscow: Metallurgiya, 1987. 480 p.
2. Tselikov А. I., Polukhin P. I., Grebenik V. М. et. al. Machines and units of metallurgical plants. In 3 volumes. Machines and assemblies for production and finishing of rolled products. Moscow: Metallurgiya, 1988. 432 p.
3. Bel’skii S. M., Mukhin Yu. A., Mazur S. I., Goncharov A. I. Influence of the cross section of hot-rolled steel on the flatness of cold-rolled strip. Steel in Translation. 2013. Vol. 43. No. 5. pp. 313–316.
4. Bel’skii S. M., Mukhin Yu. A. Classification of regulation principles for strip flatness. Steel in Translation. 2009. Vol. 39. No. 11. pp. 1012–1015.
5. Predeleanu M., Gilormini P. Advanced methods in materials processing defects. Elsevier Science. 1997. Vol. 45. 422 p.
6. Rees D. Basic engineering plasticity. An introduction with engineering and manufacturing applications. Butterworth-Heinemann, 2006. 528 p.
7. Wilko C. E. Formability. A review of parameters and processes that control, limit or enhance the formability of sheet metal. Heidelberg: Springer, 2011. 112 p.
8. Shinkin V. N. Geometry of steel sheet in a seven-roller straightening machine. Steel in Translation. 2016. Vol. 46. No. 11. pp. 776–780.
9. Shinkin V. N. Preliminary straightening of thick steel sheet in a sevenroller machine. Steel in Translation. 2016. Vol. 46. No. 12. pp. 836–840.
10. Lim Y., Venugopal R., Ulsoy A. G. Process control for sheet-metal stamping process modeling, controller design and stop-floor implementation. Springer, 2014. 140 p.
11. Lin J., Balint D., Pietrzyk M. Microstructure evolution in metal forming processes. Woodhead Publishing, 2012. 416 p.
12. Belskiy S. М. Parameters of evaluation of shape cross section of hotrolled strip steels. Part 1. The determination coefficient. Chernye Metally. 2017. No. 10. pp. 65–70.
13. Belskiy S. М. Parameters of evaluation of shape cross section of hotrolled strip steels. Part 2. The saddle coefficient. Chernye Metally. 2017. No. 11. pp. 42–47.
14. Banabic D. Multiscale modeling in sheet metal forming. Springer, 2016. 405 p.
15. Frank V. Lecture notes in production engineering. Springer, 2013. 211 p.
16. Calladine C. R. Plasticity for engineers. Theory and applications. Woodhead Publishing, 2000. 328 p.
17. Shinkin V. N. Springback coefficient of the main pipelines’ steel largediameter pipes under elastoplastic bending. CIS Iron and Steel Review. 2017. Vol. 14. pp. 28–33.
18. Shinkin V. N. Calculation of technological parameters of O-forming press for manufacture of large-diameter steel pipes. CIS Iron and Steel Review. 2017. Vol. 13. pp. 33–37.
19. Hingole R. S. Advances in metal forming. Expert system for metal forming. Springer, 2015. 116 p.
20. Chakrabarty J. Applied plasticity. Springer, 2010. 758 p.
21. Klocke F. Manufacturing processes 4. Forming. Springer, 2013. 516 p.
22. Shinkin V. N. Asymmetric three-roller sheet-bending systems in steelpipe production. Steel in Translation. 2017. Vol. 47. No. 4. pp. 235–240.
23. Hastie T., Tibshirani R., Friedman J. The elements of statistical learning. Data mining, inference and prediction. Springer, 2017. 745 p.
24. Draper N., Smith H. Applied Regression Analysis. In 2 books. Book 1. Moscow: Finansy i statistika, 1986. 366 p.
25. Lvovsky E. N. Statistical methods for construction of empirical formulas. Moscow: Vysshaya shkola, 1982. 224 p.

Language of full-text russian
Full content Buy
Back