Journals →  CIS Iron and Steel Review →  2019 →  #1 →  Back

Certification and Standardization
ArticleName The conformity assessment of metamaterials quality management
DOI 10.17580/cisisr.2019.01.10
ArticleAuthor O. I. Boriskin, G. A. Nuzhdin, E. I. Khunuzidi, D. I. Blagoveshchenskiy
ArticleAuthorData

Tula State University (Tula, Russia):

O. I. Boriskin, Dr. Eng., Prof., Head of the Chair of Instrumental and Metrological Systems, Director of Polytechnic Institute

 

National University of Science and Technology “MISiS” (Moscow, Russia):
G. A. Nuzhdin, Cand. Eng., Associate Prof., E-mail: nuzhdin65@mail.ru
E. I. Khunuzidi, Cand. Eng.

 

State Regional Center for Standardization, Metrology and Testing in Tula Region (Tula, Russia):
D. I. Blagoveshchenskiy, Cand. Eng., Associate Prof.

Abstract

The issues of quality management and ensuring compliance with the requirements of the certification body conducting conformity assessment and quality control of metamaterials. The variety of metamaterials determines a large number of technologies of their production. For many metamaterials it is necessary to carry out not only tests, but also the control of processes providing technology check and modeling of technological operations. When checking the actual execution of the technological process, the possibility of traceability of products from metamaterials throughout the technological cycle is estimated. Cross-checked against the recording required data such as the card heats of registration of the passport. Technological operations are modeled and their metrological support is evaluated. In the formed database of technological parameters of production identification and traceability of suppliers of melting and casting units, furnaces for homogenization, the deforming equipment, furnaces for heat treatment in relation to production of each concrete metamaterial shall be provided. For example, the execution of works on assessment of technologies for the manufacturing of composites with the certification of their production shows areas where necessarily require the particular attention of experts. For a representative sample, including 53 parties submitted the map middle and map scale. On the example of the coincidence of activities of a legal entity and a certification body accredited and operating on the basis of the University, the conditions of compliance with the law of conformity assessment of metamaterials, as well as products and products from them are shown. It is shown that the data and the results of its evaluation of the quality of the metamaterial and stability of the technological process should be analysed and checked by the members of the Commission with regard to mandatory corporate culture employees. Recommendations for procedural support and actions to confirm compliance are given.

The authors Express their gratitude to the staff and management of the Testing laboratory “Tekhpolikom” and NPF “Tekhpolikom” and a special tribute to the Winner of the State prize of Russia in science and technology L. I. Anikhovskaya for qualified help and professional advice.

keywords Metamaterials, conformity assessment, quality assurance, certification works, independence, impartiality, certification body, accreditation
References

1. Liu Y.-H., Liu H., Zhao X.-P. Isotropic negative permeability metamaterials and left-handed metamaterials based on miniature structure. Wuli Xuebao / Acta Physica Sinica. 2012. Vol. 61. No. 8. pp. 84–103.
2. Boriskin O. I., Blagoveshchenskiy D. I., Ezhova N. P., Nuzhdin G. A., Perminov A. S. Metrological provision of testing of magnetic materials. Chernye metally. 2017. No. 12. pp. 40–45.
3. Lukina N. F., Dementyeva L. A., Anikhovskaya L. I. Glued prepregs — promising material for metal-polymer structures. Welding International. 2015. Vol. 29. No. 7. pp. 573–576.
4. ISO/IEC 17067:2013 Conformity assessment — Fundamentals of product certification and guidelines for product certification schemes.
5. ISO/IEC 17000:2004 Conformity assessment — Vocabulary and general principles.
6. ISO/IEC 17065:2012 Conformity assessment — Requirements for bodies certifying products, processes and services.
7. Kiss I., Maksay S. Bimetallic cast iron rolls — some approaches to assure the exploitation properties. Tehnicki Vjesnik. 2010. Vol. 17. No. 2. pp. 173–178.
8. Minakov V. F., Minakova T. E. Remote monitoring systems for quality management metal pouring. Lecture Notes in Control and Information Sciences. 2015. Vol. 22. pp. 63–71.
9. Rudometov Y. Quality control in the production of metal-cutting tools. Russian Engineering Research. 2014. Vol. 34. No. 6. pp. 400–401.
10. Levkov L. et al. Study of the effect of melting rate on electroslag remelted hollow steel billet quality. Metallurgist. 2014. Vol. 58. No. 7-8. pp. 677–683.
11. Grin E. A., Anokhov A. E., Pchelintsev A. V., Krüger E.-T. Study of the structure and properties of metal of the major steam lines of a CCGT-420 unit made from high-chromium Х10CRMOVNB9-1 (P91) steel. Thermal Engineering. 2016. Vol. 63. No. 7. pp. 471–480.
12. Mitin O. N., Nuzhdin G. A., Nguyen K. H. Simulation of crimping operation with thinning of thick-walled pipe billets. Izvestiya Tulskogo gosudarstvennogo universiteta. Technical sciences. 2014. Issue 5. pp. 57–65.
13. Mitin O. N., Nuzhdin G. A., Nguyen K. H. Rules of influence of technological parameters on stress distribution heterogeneity along the thickness of a billet during the crimping of thick-walled pipe billets. Izvestiya Tulskogo gosudarstvennogo universiteta. Technical sciences. 2014. Issue 6. pp. 46–53.
14. Nuzhdin G. A. Technology of hardening cutting plates from superhard composites. Uprochnyayushchie tekhnologii i pokrytiya. 2005. No. 7. pp. 49–50.
15. Batizat D. V., Sakharov A. M., Yarosh A. A., Anikhovskaya L. I., Barbotko S. L. Noncombustible adhesive compositions based on brominated epoxide resins for production of structural film adhesives and adhesive prepregs. Polymer Science. Series D. 2016. Vol. 9. No. 3. pp. 298–302.
16. Plekhanov V. Sh., Samoshkin Iu. A., Nuzhdin G. A. The certification quality assessment. Reference information. Inzhenernyi zhurnal. 2012. No. 4. pp. 36–40.
17. ISO 472:1999 Plastics — Vocabulary.
18. Baritko N. V. et al. Manual R SCM-02-2017. Interstate Aviation Committee. Aviation register. 2017. Vol. 5. 20 p.
19. Larin S. N., Nuzhdin G. A., Tregubov V. I. Power modes and limiting deformation of three-layer structures with trapezoidal channels in short-term creep mode. Izvestiya Tulskogo gosudarstvennogo universiteta. Technical sciences. 2018. Issue 4. pp. 14–20.
20. Baritko N.V. et al. Manual R RMS-04-2017. Interstate Aviation Committee. Aviation register. 2017. Vol. 6. 31 p.
21. Order of the Ministry of Economic Development of the Russian Federation dated May 30, 2014 No. 326 (as amended on March 17, 2017). Registered by the Ministry of Justice of the Russian Federation under No. 33362 on July 30, 2014.
22. Plekhanov V. Sh., Samoshkin Yu. A., Kuleshov E. V., Nuzhdin G. A., Khunuzidi E. I. Application of regulatory documents to assess the conformity of quality management systems. Nanoinzheneriya. 2014. No. 11. pp. 44–48.
23. ISO/IEC 17021:2011 Conformity assessment — Requirements for bodies providing audit and certification of management systems.

Full content The conformity assessment of metamaterials quality management
Back