Journals →  Chernye Metally →  2019 →  #3 →  Back

Foundry Processes and Metal Science
ArticleName Direct and inverse non-linear approximation of hardening zone of steel
ArticleAuthor V. N. Shinkin
ArticleAuthorData

National University of Science and Technology “MISIS” (Moscow, Russia):

V. N. Shinkin, Dr. Phys.-Math., Prof., e-mail: shinkin-korolev@yandex.ru

Abstract

The mechanical properties of steels and alloys play an important role in the production of the steel products from the steel sheet and straight beam (with the round and rectangular crosssections). Experimentally, the mechanical properties are studied on the universal tensile machines, which can stretch, compress or twist the steel specimens of standard shape. For example, under a tension of the round or flat steel specimen, made from a low-carbon steel, in an electromechanical universal testing machine, we get the classic diagram “stress - relative elongation” (the diagram of the dependence of the normal stress on the relative elongation of the specimen). We define the two most important mechanical characteristics of steels on the diagram - the yield strength and the ultimate strength. At the beginning of the diagram, there is a linear zone of the stress-strain dependence obeying the linear Hooke’s law for the elastic deformations (up to the proportionality limit). Then there is a small zone from the proportionality limit through the elastic limit to the yield point (usually this zone is neglected in the analytical and numerical calculations). Then on the diagram we clearly see the non-linear hardening zone (the zone of the irreversible plastic deformations), which begins at the end of the yield area (the yield point) and ends at the time of the neck’s formation (at the time of the reaching of the ultimate strength). Behind the hardening zone, there is the local fluidity zone in the neck’s area. At the end of the local fluidity zone, the specimen’s rupture takes place. In metallurgy and mechanical engineering, the elastic-plastic deformation of steel billets is carried out in the zone of the steel’s plastic hardening (usually in the first half of the hardening zone). It is not recommended to come close to the second rear half of the steel’s hardening zone during the billet’s deformation, as in this case there is a high risk of an appearance of the surface and internal hidden defects of the steel billet, which are almost impossible to eliminate during the subsequent stages of metal product. Under the numerical and mathematical modeling of processes of hot and cold deformation of steel products, it is essential to know the analytical dependence (approximation) of stresses on strains in the steel’s hardening zone. The most well-known classical approximations of the steel’s hardening zone are the simplest Prandtl’s approximation, the linear approximation, and the non-linear approximations by Nadai and Ludwik. However, all of them are not without significant drawbacks, as they offer to approximate the non-linear hardening curve by only one term (a power function). Below we propose other methods of the direct and inverse non-linear approximations using the finite or infinite power series with the displacement of the argument (relative deformation). The series members can have both integer and fractional power, and the coefficients of the series members can have both positive and negative values. It is shown that this method is much more accurate than the classical approximation methods.

keywords Elastic and plastic deformation, non-linear hardening zone of low-carbon steel, yield strength, ultimate strength, direct and inverse approximation
References

1. Nadai A. Theory of flow and fracture of solids. Vol. 1. Moscow : Inostrannaya Literatura, 1954. 648 p.
2. Ludwik P. Elemente der Technologischen Mechanik. Springer, 1909. 57 s.
3. Smirnov-Alyaev G. A. Resistance of materials to plastic deformations. Moscow; Leningrad : Mashgiz, 1949. 248 p.
4. Birger I. A. Residual stresses. Moscow : Mashgiz, 1963. 232 p.
5. Moshnin E. N. Bending and straightening on rotary machines. Technology and equipment. Moscow : Mashinostroenie, 1967. 272 p.
6. Shinkin V. N. Springback coefficient of the main pipelines’ steel large-diameter pipes under elastoplastic bending. CIS Iron and Steel Review. 2017. Vol. 14. pp. 28-33.
7. Shinkin V. N. Arithmetical method of calculation of power parameters of 2N-roller straightening machine under flattening of steel sheet. CIS Iron and Steel Review. 2017. Vol. 14. pp. 22-27.
8. Chakrabarty J. Applied plasticity. Springer, 2010. 758 p.
9. Rees D. Basic engineering plasticity. An introduction with engineering and manufacturing applications. Butterworth-Heinemann, 2006. 528 p.
10. Calladine C. R. Plasticity for engineers. Theory and applications. Woodhead Publishing, 2000. 328 p.
11. Mozgunov V. N., Serov M. V., Zubarev A. A. Stability investigations of three-layer cylindrical shells with a grid filler. Chemical and Petroleum Engineering. 1997. Vol. 33, No. 3. pp. 272-277.
12. Mozgunov V. N., Serov M. V., Zubarev A. A. Stability of a three-layer shell made of a composite material with a reticular filler. Chemical and Petroleum Engineering. 1994. Vol. 30, No. 10. pp. 480-485.
13. Shinkin V. N. Failure of large-diameter steel pipe with rolling scabs. Steel in Translation. 2017. Vol. 47, No. 6. pp. 363-368.
14. Shinkin V. N. Simplified calculation of the bending torques of steel sheet and the roller reaction in a straightening machine. Steel in Translation. 2017. Vol. 47, No. 10. pp. 639-644.
15. Klocke F. Manufacturing processes 4. Forming. Springer, 2013. 516 p.
16. Banabic D. Sheet metal forming processes. Constitutive modelling and numerical simulation. Springer, 2010. 301 p.
17. Chakrabarty J. Theory of plasticity. Butterworth-Heinemann, 2006. 896 p.
18. Mozgunov V. N., Serov M. V., Zubarev A. A. Research of stability of the three-layer cylindrical shells with netted filler. Khimicheskoe i Neftegazovoe Mashinostroenie. 1997. No. 3. pp. 23-26.

19. Mozgunov V. N., Serov M. V., Zubarev A. A. Stability of a three-layer shell made of composite material with a net-like filler. Khimicheskoe i Neftegazovoe Mashinostroenie. 1994. No. 10. pp. 15-17.
20. Shinkin V. N. Preliminary straightening of steel strip. Chernye Metally. 2018. No. 5. pp. 34-40.
21. Frank V. Lecture notes in production engineering. Springer, 2013. 211 p.
22. Hingole R. S. Advances in metal forming. Expert system for metal forming. Springer, 2015. 116 p.
23. Banabic D. Multiscale modelling in sheet metal forming. Springer, 2016. 405 p.

Language of full-text russian
Full content Buy
Back