Журналы →  CIS Iron and Steel Review →  2018 →  №2 →  Назад

Название Protective coatings produced by electro-spark deposition with TiCNiCr–(Eu2O3) electrodes
DOI 10.17580/cisisr.2018.02.12
Автор F. V. Kiryukhantsev-Korneev, A. D. Sytchenko, A. E. Kudryashov, E. A. Levashov
Информация об авторе

National University of Science and Technology “MISiS” (Moscow, Russia):

Ph. V. Kiryukhantsev-Korneev, Cand. Eng., Associate Prof., Department of Powder Metallurgy and Functional Coatings; Leading Researcher, Scientific and Educational Center SHS MISiS-ISMAN, e-mail: kiruhancev-korneev@yandex.ru
A. D. Sytchenko, Laboratory Assistant, Scientific and Educational Center SHS MISiS-ISMAN
A. E. Kudryashov, Cand. Eng., Leading Researcher, Scientific and Training Center SHS MISiS-ISMAN
E. A. Levashov, Dr. Eng., Prof., Head of the Department of Powder Metallurgy and Functional Coatings; Director, Scientific and Educational Center SHS MISiS-ISMAN


This paper examines coatings deposited on 40x (analog of 5140) steel substrates by electro-spark alloying with TiCNiCr and TiCNiCr–Eu2O3 electrodes. The techniques of X-ray phase analysis, scanning electron microscopy, energy dispersive X-ray spectroscopy and glow-discharge optical emission spectroscopy were applied to analyze the structure, as well as the elemental and phase compositions of the coatings. The mechanical and tribological properties of the coatings were analyzed with the help of nanoindentation and pin-on-disk tests. The coatings were also subjected to electrochemical testing and annealing. The obtained results did not reveal any significant difference between the coatings with Eu2O3 in terms of the structure and friction coefficient. However, in terms of heat and corrosion resistance, the coatings with Eu2O3 outperform the basic ones. The doped coatings had a more than 20 times lower corrosion current and almost 2 times lower the oxidation number compared with undoped coatings. It is shown that due to the developed coatings the steel parts can be 2.5 times harder, 7 times more wear resistant (with half as high the friction coefficient), more than 20 times more corrosion resistant, and 18 times more heat resistant.

This research was funded by the Ministry of Education and Science of Russia (Assignment No. 11.7172.2017/8.9).
The authors thank A. N. Sheveyko and N. V. Shvyndina for their support with electrochemical testing and structural analysis of the coatings.

Ключевые слова TiC–Ni, europium oxide, electro-spark alloying, steel, coating, structure, hardness, friction coefficient, mechanical and tribological properties, corrosion resistance, oxidation resistance, oxidation kinetics
Библиографический список

1. Gerasimova A. A., Radyuk A. G. The improvement of the surface quality of workpieces by coating. CIS Iron and Steel Review. 2014. Vol. 9. pp. 33–35.
2. Verkhoturov A. D., Mukha I. M. Electrospark alloying technology. Kiev : Tekhnika. 2002. 182 p.
3. Agudelo-Morimitsu L. C., De La Roche J., Rudena A., Escobar D., Restrepo-Parra E. Effect of substrate temperature on the mechanical and tribological properties of W/WC produced by DC magnetron sputtering. Ceramics International. 2014. Vol. 40. pp. 7037–7042.
4. Nikolenko S. V., Kuzmenko A. P., Timakov D. I., Abakymov P. V. Nanostructuring a steel surface by electrospark treatment with new electrode materials based on tungsten carbide. Surface Engineering and Applied Electrochemistry. 2011. Vol. 47. pp. 217–224.
5. Villiers H. L. Lovelock, powder/processing/structure relationships in WC–Co thermal spray coatings: a review of the published literature. Journal of Thermal Spray Technology. 1998. Vol. 7. pp. 357–373.
6. Nikolenko S. V., Syuy N. A., Burkov A. A. Investigation of microstructure and properties of coatings on the steel 45, applied by TiC — Ni — Mo based electric discharge deposition. Tsvetnye Metally. 2017. No. 4. pp. 69–75.
7. Panteleenko F. I., Sarantsev V. V., Stolin A. M., Bazhin P. M., Azarenko E. L. Formation of composite coatings based on titanium carbide via electrospark alloying. Surface Engineering and Applied Electrochemistry. 2011. Vol. 47. pp. 336–348.
8. Andreev A. V., Litovchenko I. Y., Korotaev A. D., Borisov D. P. Thermal Stability of Ti–C–Ni–Cr and Ti–C–Ni-Cr–Al–Si Nanocomposite Coatings. Journal of Physics: Conference Series. 2015. Vol. 652. pp. 012057.
9. Levashov E. A., Kudryashov A. E., Vakaev P. V., Malochkin O. V., Gammel F., Suchentrunk R., Moore J. J. The prospect of Nanodispersive Powders Application in Surface Technologies. Surface and Coating Technologies. 2004. Vol. 180-181. pp. 347–351.
10. Izraelyants K. R., Orlov A. P., Ormont A. B., Chirkova E. G. Effect of the cesium and potassium doping of multiwalled carbon nanotubes grown in an electrical arc on their emission characteristics. Physics of the Solid State. 2017. Vol. 59. pp. 838–844.
11. Kong J. T., Shi S. Y., Kong L. C., Zhu X. P., Ni J. R. Preparation and characterization of PbO2 electrodes doped with different rare earth oxides. Electrochimica Acta. 2007. Vol. 53. pp. 2048–2054.
12. Hua G., Li D. Generic relation between the electron work function and Young’s modulus of metals. Applied Physics Letters. 2011. Vol. 99. pp. 041907.
13. Fang Y., Cui X., Cai Z., Wang C., Jin G. Influence of La2O3 addition on nano indentation hardness and residual stress of Stellite 6 coating prepared by plasma cladding. Journal of Rare Earths. 2018. DOI: 10.1016/j.jre.2018.03.008.
14. Zhao T., Xun C., Wang S. X., Zheng S. A. Effect of CeO2 on microstructure and corrosive wear behavior of laser-cladded Ni/WC coating. Thin Solid Film. 2000. Vol. 379. pp. 128–132.
15. Li J., Luo X., Li G. J. Effect of Y2O3 on the sliding wear resistance of TiB/TiC-reinforced composite coatings fabricated by laser cladding. Wear. 2014. Vol. 310. pp. 72–82.
16. Li J., Wang H. P., Li M. P., Yu Z. S. Effect of yttrium on microstructure and mechanical properties of laser clad coatings reinforced by in situ synthesized TiB and TiC. Journal of Rare Earths. 2011. Vol. 29. pp. 477–483.
17. Zhu R., Li Z., Li X., Sun Q. Microstructure and properties of the low-power-laser clad coatings on magnesium alloy with different amount of rare earth addition. Applied Surface Science. 2015. pp. 353–405.
18. Kiryukhantsev-Korneev Ph. V., Sheveyko A. N., Shvindina N. V., Levashov E. A., Shtansky D. V. Comparative study of Ti–C–Ni–Al, Ti–C–Ni–Fe, and Ti–C–Ni–Al/Ti–C–Ni–Fe coatings produced by magnetron sputtering, electro-spark deposition, and a combined two-step process. Ceramics International. 2018. Vol. 44. pp. 7637–7646.
19. Kiryukhantsev-Korneev Ph. V., Sytchenko А. D., Kudryashov А. Е., Levashov E. A., Shtansky D. V. The Effect of Eu2O3 Additive to the TiCNiCr Electrode on the Formation of Electrospark Coatings. Technical Physics Letters. 2018. Vol. 44. pp. 753–755.
20. Ahlawat R., Rani N., Goswami B. Synthesis and characterizations of Eu2O3 nanocrystallites and its effect on optical investigations of Eu3+, Eu2+: SiO2 nanopowder. Journal of Alloys and Compounds. 2018. Vol. 743. pp. 126–135.
21. Niu T., Zhang P., Zheng G., Liu l., Deng J., Jin Y., Jiao Z., Sun X. Tuning the charge transition process of Eu2O3 nanorods by coupling with Ag nanoparticles for enhanced photocatalytic performance. Journal of Environmental Chemical Engineering. 2017. Vol. 5. pp. 2930–2936.
22. Hui Y., Zhao S. M., Xu J. Y. Doping concentration of Eu3+ as a fluorescence probe for phase transformation of zirconia. Journal of Rare Earths. 2015. Vol. 33. pp. 717–725.
23. Paustovskii A. V., Gubin Yu. V. Stresses in coatings obtained by electro-spark alloying and laser processing (review). Materials Science. 1997. Vol. 33. pp. 770–776.
24. Chen Z., Zhou Y. Surface modification of resistance welding electrode by electrospark deposited composite coatings: part I. Coating characterization. Surface Coating Technology. 2006. Vol. 201. pp. 1503–1510.
25. Leyland A., Matthews A. On the significance of the H/E ratio in wear control: a nanocomposite coating approach to optimised tribological behavior. Wear. 2000. Vol. 246. pp. 1–11.
26. Murthy T. K. S., Gupta C. K. Rare earth resources, their extraction and applications. The Science and Technology of Rare Earth Materials. 1980. pp. 3–23.
27. Ozgurluk Y., Doleker K. M., Ahlatci H., Karaoglanli A. C. Investigation of hot corrosion behavior of thermal barrier coating (TBC) systems with rare earth contents. Arabian Journal of Geosciences. 2018. 11:267.
28. Lavrenko V. A., Glebov L. A., Pomitkin A. P., Chuprina V. G., Protsenko T. G. High-temperature oxidation of titanium carbide in oxygen. Oxidation of Metals. 1975. Vol. 9. pp. 171–179.

Полный текст статьи Protective coatings produced by electro-spark deposition with TiCNiCr–(Eu2O3) electrodes