Journals →  Tsvetnye Metally →  2017 →  #10 →  Back

BENEFICATION
ArticleName Comparison of ore comminution technologies using SAG mill and roller-press for Udokan copper deposit ores
DOI 10.17580/tsm.2017.10.05
ArticleAuthor Senchenko A. E., Kulikov Yu. V.
ArticleAuthorData

Science-research and design Institute “TOMS” LLC, Irkutsk, Russia:

A. E. Senchenko, General Director, e-mail: senchenko@tomsmineral.ru
Yu. V. Kulikov, Chief Technologist

Abstract

This paper shows the results from comparison of the possible comminution circuits and validation of an efficient circuit for its implementation at the Udokan plant. Results of the ore testing in a pilot roller-press (HPGR technology) and data on the ore grindability through semi-autogenious grinding (SAG technology) are presented in the paper. The testing defined the principal possibility of HPGR application for Udokan deposit ore. This ore was found to be favorable material for treatment in the HPGR. It was also established that Udokan deposit ores are highly refractory to the SAG process. The difference in the installed capacity of equipment between circuits with HPGR and SAG mill varied from 36 to 40% depending on the circuit configuration. Besides the energy saving, considerable reduction of OPEX is expected for the HPGR circuit in view of lower consumption of balls and lining. Unlike the earlier designed process procedures and project, on the basis of the obtained data set a comminution circuit was recommended with the ore crushing in the roller-press in close cycle with wet screening at 6.3 mm. The final decision on the choice of optimal comminution circuit for the plant at Udokan copper deposit should be made based on technical and economic comparison of circuit options taking into account CAPEX and OPEX. The preliminary technical and economic calculations made by manufacturers of grinding and crushing equipment for similar projects indicate that the cost of the basic equipment of the HPGR circuit is comparable or little higher than the one of the SAG circuit; however the OPEX of the HPGR circuit are considerably lower.

keywords Udokan copper deposit, grinding, crushing, SAG, abrasivity, mill, roller-press, HPGR
References

1. Senchenko A. Y., Kulikov Y. V. Special aspects of circuits design with the use of HPGR technology based on pilot testing data and industrial operating experience. IMPC XXVIII Congress 2016.
2. Fedotov P. K., Fedotov K. V. High-pressure roller mills (roller-presses). Moscow : Geoinformmark, 2006. 128 p.
3. Heinicke F., Günter H., Lieberwirthand H., Popov O. Mathematical-petrographic rock characterization as support for HPGR sizing. SAG Conference 2015.
4. Comi T., Burchardt E. A premiere for Chile: the HPGR based copper concentrator of sierra gorda SCM. SAG Conference 2015.
5. Vanderbeek J. L., Gunson A. J. Cerro Verde 240,000 t/d concentrator expansion. SAG Conference 2015.
6. Herman V. S., Harbold K. A., Mular M. A., Biggs L. J. Building the world’s largest HPGR — the HRCTM 3000 at the morenci metcalf concentrator. SAG Conference 2015.
7. Starkey J., Hindstrom S., Nadasdy G. SAGDesign testing — what it is and why it works. SAG Conference 2006.
8. Starkey J. H., Meadows D., Thompson P., Senchenko A. SAGDesign testing review – case studies. IMPC XXIV Congress 2008.
9. Starkey J., Samuels M. New discoveries in the relationship between macro and micro grindability. CIM AGM 2009.
10. Starkey J., Scinto P. SAG mill grinding design versus geometallurgy – getting it right for competent ores. IMPC XXV Congress 2010.
11. Starkey J., Larbi K. SAGDesignTM – using open technology for mill design and performance assessments. 9th International Mineral Processing Conference (Procemin 2012).
12. Technological regulations for designing the dressing plant at Udokan deposit. Irkutsk : Institut TOMS, 2014.
13. Rosario P. P., Drozdiak J. A., Tse W. Economic and operational assessment of a non-conventional HPGR circuit. IMPC XXVIII Congress 2016.
14. van der Meer F. Comparison of HPGR (Roller Press) and SAG mill grinding circuits. Compilation of Selected Project Data. Cologne 2006.

Language of full-text russian
Full content Buy
Back