Journals →  Tsvetnye Metally →  2017 →  #9 →  Back

COMPOSITES AND MULTIPURPOSE COATINGS
ArticleName Modeling of regeneration process of special alloys’ spent powders after layer-by-layer manufacturing of polymetallic products
DOI 10.17580/tsm.2017.09.10
ArticleAuthor Yuzhakova E. A., Beshkarev V. T., Trofimov K. I., Khomyakov S. G.
ArticleAuthorData

Moscow University of Science and Technology MISiS, Moscow, Russia:

E. A. Yuzhakova, Post-Graduate Student of a Chair of Physical Materials Science, e-mail: lee_na@mail.ru

 

JSC “Giredmet”, Moscow, Russia:
V. T. Beshkarev, Leading Researcher of Laboratory of Rare, Refractory and High-Pure Metals Obtaining Technology

 

Ural Plant of Gas Centrifuges, Novouralsk, Russia:
K. I. Trofimov, Leading Mathematician of Calculation and Design Engineering Department
S. G. Khomyakov, Head of a Project

Abstract

Our paper offers the option of a modular device for regeneration of spent powder mixtures after layer-by-layer synthesis of polymetallic items. Depending on variants of the composition of the used powders, the device may include interchangeable modules of electromagnetic, sieve or gas-dynamic classification. High-vacuum and high-temperature degassing module should be included in the powder composition regeneration system to remove adsorbed gases from the particle surface. For the separation of powder composition, formed using two powders of the same fineness and different magnetic properties, it is advisable to use the electromagnetic separation module. In case of using powders with same basis elements and with comparable density values, the gas-dynamic classification module should be applied. Using the methods of mathematical and experimental modeling, it is shown a comparison of the effectiveness of different waste powder mixtures separation types and classifiers such as “zigzag”, “cyclone” and “dust camera”. It is shown that the modular classifier based on dust camera provides the necessary functionality: divides multipowder mixture into fractions of predetermined particle size. The possibility of applying centrifugal classifier with the option of separation of powder mixtures in an inert atmosphere to work with powders based on active metals was discussed. On the basis of relations established in the modeling of vacuum degassing processes of waste classified polymetallic powder mixtures, it was revealed the efficiency of degassing of thin or moving layers of powder. To improve the profitability of additive production of titanium based items it was offered the method for recycling of waste products. The technology involves the sequential operations of hydrogenation, crushing, dehydrogenation, classification and plasma spheroidization to obtain the source powders for use in additive technologies.

keywords Additive technologies, polymetallic powder mixture, regeneration, classification, vacuum degassing
References

1. Vostrikov A. V., Sukhov D. I. The production of powders by PREP method for additive manufacturing – current situation and development prospects. Trudy VIAM. 2016. No. 8. DOI: 10.18577/2307-6046-2016-0-8-3-3
2. Petrik I. A., Ovchinnikov A. V., Seliverstov A. G. Development of titanium alloy powders for additive technologies as applied to gas-turbine engine details. Aviatsionno-kosmicheskaya tekhnika i tekhnologiya. 2015. No. 8. pp. 11–16.
3. Dzhugan A. A., Ovchinnikov A. V., Olshanetskiy V. E. Additive techno logies and capabilities of their applications in modern conditions (review). Novі materіali і tekhnologі v metalurgi ta mashinobuduvannі. 2014. No. 2. pp. 97– 101.
4. Reichardt A., Dillon R. P., Borgonia J. P., Shapiro A. A., McEnerney B. W., Momose T., Hosemann P. Development and characterization of Ti – 6 Al – 4 V to 304 L stainless steel gradient components fabricated with laser deposition additive manufacturing. Materials & Design. 2016. Vol. 104. DOI: 10.1016/j.matdes.2016.05.016
5. Kundu S., Sam S., Chatterjee S. Evaluation of interface microstructure and mechanical properties of diffusion bonded joints of Ti – 6 Al – 4 V alloy to micro-duplex stainless steel. Materials Science and Engineering: А. 2011. Vol. 528. pp. 4910–4916.
6. Duplishcheva E. E., Babakova E. V. Methods of processing of SLS-production wastes. Ecology and safety in technosphere: modern problems and ways of their solving : collection of proceedings of All-Russian scientific-practical conference of young scientists, post-graduate students and students. Yurga, 5–6 November 2015 : in two volumes. Tomsk : TPU, 2015. Vol. 1. pp. 311–313.
7. Belov A. F. et al. Processes of treatment of light and heat-resistant alloys. Moscow : Nauka, 1981. pp. 151–162.
8. Khairallah S. A., Anderson A. T., Rubenchik A., King W. E. Laser powder-bed fusion additive manufacturing: physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones. Acta Materialia. 2016. Vol. 108. pp. 36–45.
9. Bauerei A., Scharowsky T., Körner C. Defect generation and propagation mechanism during additive manufacturing by selective beam melting. Journal of Materials Processing Technology. 2014. Vol. 214, No. 11. pp. 2522–2528.
10. Glazunov S. G., Borzetsovskaya K. M. Powder metallurgy of titanium alloys. Moscow : Metallurgiya, 1989. 136 p.
11. Ivasishin O. M., Savvakin D. G., Bondareva K. A., Mokson V. S., Duz V. A. Production of titanium alloys and details using economic method of powder metallurgy for wide-scale industrial application. Nauka ta іnnovatsi. 2005. Vol. 1, No. 2. pp. 44–57.
12. Sames W. J., List F. A., Pannala S., Dehoff R. R., Babu S. S. The metallurgy and processing science of metal additive manufacturing. International Materials Reviews. 2016. DOI: 10.1080/09506608.2015.1116649

Language of full-text russian
Full content Buy
Back