Journals →  CIS Iron and Steel Review →  2016 →  #2 →  Back

ArticleName The mathematical model of the thick steel sheet flattening on the twelve-roller sheet-straightening machine. Message 1. Curvature of sheet
DOI 10.17580/cisisr.2016.02.08
ArticleAuthor V. N. Shinkin
ArticleAuthorData

National University of Science and Technology “MISIS”, Moscow, Russia

V. N. Shinkin, DSc. Phys.-Math., Prof., shinkin-korolev@yandex.ru

Abstract

The mathematical method for the determining of the optimal technological parameters of the cold straightening of the thick steel sheet on the twelve-rolled sheet-straightening machine is proposed. The calculations allow us to determine the type and the curvature of the neutral line of the steel sheet under the straightening depending on the rolls’ radius, the pitch between the straightening machines’ working rolls, the magnitude of the sheet reduction by the upper rollers, the sheet thickness, as well as the elastic modulus, the yield stress and the hardening modulus of the sheet metal. The results of the research can be used at the metallurgical plants.

keywords Steel sheet, sheet-straightening machines, curvature of sheet, springback coefficient, elastoplastic continuous medium
References

1. Korolev A. A. Mekhanicheskoe oborudovanie prokatnykh I trubnykh tsekhov (Mechanical equipment of rolling and pipe shops). Moscow : Metallurgiya. 1987.
2. Tselikov A. I., Poluhin P. I., Grebenik V. M. et al. Mashiny i agregaty metallurgicheskikh zavodov (Machines and units of metal lurgical plants). Vol. 3. Moscow : Metallurgy. 1998.
3. Kotsar S. L., Tretyakov V. A., Belskiy S. M., Polyakova B. A., Savochkin A. G. Experimental verification of mathematical models of rolling with axial roll shift simulation. Steel in Translation. 1993. No. 2. pp. 53–55.
4. Belskiy S. M., Tretyakov V. A., Baryshev V. V., Kudinov S. V. Investigation of slab width formation in roughing group of broad strip mill. Steel in Translation. 1998. Vol. 28. No. 1. pp. 32–39.
5. Belskiy S. M., Mukhin Y. A. Hot strip rolling with local thicke ning. Steel in Translation. 2009. Vol. 39. No. 5. pp. 420–424.
6. Belskiy S. M., Mukhin Y. A. Classification of regulation principles for strip flatness. Steel in Translation. 2009. Vol. 39. No. 11. pp. 1012–1015.
7. Belskiy S. M., Mazur S. I., Mukhin Y. A., Goncharov A. I. Influence of the cross section of hot-rolled steel on the flatness of cold-rolled strip. Steel in Translation. 2013. Vol. 43. No. 5. pp. 313–316.
8. Muhin U., Belskiy S., Makarov E., Koinov T. Application of betweenstand cooling in the production of hot-rolled strips. Journal of Chemical Technology and Metallurgy. 2014. Vol. 49. No. 1. pp. 65–70.
9. Muhin U., Belskiy S., Koinov T. Study on the influence of the antibending force of working rolls on the widening in hot rolling of thin sheet. Journal of Chemical Technology and Metallurgy. 2014. Vol. 49. No. 1. pp. 77–81.
10. Muhin U., Belskiy S., Makarov E., Koinov T. Simulation of accelerated strip cooling on the hot rolling mill run-out roller table. Journal of Chemical Technology and Metallurgy. 2014. Vol. 49. No. 1. pp. 60–64.
11. Belskiy S. M., Yankova S., Chuprov V. B., Bakhaev K. V., Stoyakin A. O. Temperature field of stripes under hot rolling. Journal of Chemical Technology and Metallurgy. 2015. Vol. 50. No. 6. pp. 613–616.
12. Belskiy S., Mazur I., Lezhnev S., Panin E. Distribution of linear pressure of thin-sheet rolling across strip width. Journal of Chemical Technology and Metallurgy. 2016. Vol. 51. No. 4. pp. 371–378.
13. Chikalov S. G., Fadeev M. M., Kolikov A. P. Investigation of operation of process tools of TPA 159-426 continuous mill. Zhongguo Jixie Gongcheng. 1998. Vol. 9. No. 12. pp. 38–44.
14. Chikalov S. G., Fadeev M. M., Belomestnov A. K., Kuznetsov V. Yu., Kolikov A. P. Development of seamless pipe production from CC billets at TPA 159-426 unit. Shuiyun Gongcheng. 1998. No. 10. pp. 46–49.
15. Chikalov S. G., Fadeev M. M., Kolikov A. P. Mathematical model of roll-press piercing of square billets. Communication 1. Steel in Translation. 1999. Vol. 29. No. 11. pp. 74–77.
16. Chikalov S. G., Fadeev M. M., Kolikov A. P. Mathematical model of push piercing of square blooms. Report 2. Steel in Translation. 2000. Vol. 30. No. 3. pp. 69–73.
17. Lavrischev V. M., Kondratov L. A., Kolikov A. P. Pipe and tube production in Russia: Modern state and future trends. Revue de Metallurgie. 2007. Vol. 104. No. 5. pp. 250–257.
18. Kolikov A. P., Kondratov L. A. Growth of steel-tube production. Metallurgist. 2008. Vol. 52. No. 1–2. pp. 53–61.
19. Romantsev B. A., Kolikov A. P., Samusev S. V. Progress in the production of seamless and welded pipe. Steel in Translation. 2009. Vol. 39. No. 3. pp. 257–261.
20. Shinkin V. N., Kolikov A. P. Simulation of the shaping of blanks for large-diameter pipe. Steel in Translation. 2011. Vol. 41. No. 1. pp. 61–66.
21. Shinkin V. N., Kolikov A. P. Elastoplastic shaping of metal in an edge-bending press in the manufacture of large-diameter pipe. Steel in Translation. 2011. Vol. 41. No. 6. pp. 528–531.
22. Shinkin V. N., Kolikov A. P. Engineering calculations for processes involved in the production of large-diameter pipes by the SMS Meer technology. Metallurgist. 2012. Vol. 55. Nos. 11−12. pp. 833–840.
23. Osadchii V. Y., Gaas E. A., Zvonarev D. Y., Kolikov A. P. Shaping of thick sheet in the production of welded large-diameter pipe. Steel in Translation. 2014. Vol. 44. No. 5. pp. 374–378.
24. Kolikov A. P., Leletko A. S., Matveev D. B., Kadilnikov S. V., Kulyutin S. A. Residual stress in welded pipe. Steel in Translation. 2014. Vol. 44. No. 11. pp. 808–812.
25. Shinkin V. N., Fedotov O. V. Calculation of technological parameters of five-roller sheet-straightening machine by the Fagor Arrasate company under manufacture of steel sheet from hot-rolled coil. 2013. Rolling. No. 9. pp.43–48.
26. Shinkin V. N., Barykov A. M. Technological parameter calculation of cold flattening of steel sheet on nine-roller plate-flattening machine SMS Siemag at metallurgical complex of mill 5000. Rolling. 2014. No. 5. pp.7–15.
27. Shinkin V. N. Production parameter calculation for steel plate leveling at eleven-roller plate-leveling machine of cross cutting line Fagor Arrasate. Rolling. 2014. No. 8. pp.26–34.
28. Shinkin V. N. Mathematical model of steel sheet flattening on fifteenroller sheet-straightening machine of cutting-to-length line by Fagor Arrasate company. 2015. Rolling. No. 1. pp. 42–48.

Full content The mathematical model of the thick steel sheet flattening on the twelve-roller sheet-straightening machine. Message 1. Curvature of sheet
Back