Journals →  Chernye Metally →  2014 →  #4 →  Back

115th anniversary of St. Petersburg State Polytechnic University
ArticleName Control of nonmetallic inclusions formation during converter steel production
ArticleAuthor A. A. Kazakov, P. V. Kovalev, S. V. Ryaboshuk, M. V. Zhironkin, A. V. Krasnov
ArticleAuthorData

“Metallurgical technologies” Chair, St. Petersburg State Polytechnic University (St. Petersburg, Russia):

Kazakov A. A., Dr. Eng., Prof., Head of the Chair, e-mail: kazakov@thixomet.ru
Kovalev P. V., Cand. Eng., Assist. Prof.
Ryaboshuk S. V., Assistant

 

Severstal JSC (Cherepovets, Russia):

Zhironkin M. V., Ladle Treatmet Manager, Steel Competence Center
Krasnov A. V., Chief Technologist, Steelmaking Production

Abstract

Nature of formation and special evolution features of nonmetallic inclusions during ladle refining of converter HSLA steels for pipelines have been studied. Nonmetallic inclusions of the CaO–Al2O3–MgO system, close to calcium monoaluminate CaO∙Al2O3 with up to 5–6% of MgO, have been found as favorable from morphology point of view. These small inclusions nucleate on endogenous MgO substrates at sufficient high content of calcium in steel melt. Hot rolled plates can be rejected due to the coarse calcium bi- and hexa-aluminate inclusions (CaO∙2Al2O3 and CaO∙6Al2O3), usually containing exogenous MgO. These coarse inclusions are forming under calcium deficiency conditions, especially in the case of longtime steel holding in a ladle. Critical parameters and technological recommendations providing low level of nonmetallic inclusions in steel have been formulated: calcium/aluminum ratio used for steel deoxidation and modifi cation was increased; interval between additions of calcium and aluminum was decreased; full time of refining was corrected; procedures for lowering of steel reoxidation during pouring were conducted. Twenty five heats were carried out according to recommendations and the specimens from 128 hot-rolled plates were investigated for evaluation of nonmetallic impurity rating of steel. Metallographic analysis revealed that 95% of finished plates had rate up to 2.0 according to GOST 1778-70 (Sh6 method) standard.

keywords Nonmetallic inclusions, pipeline steel, deoxidation, modification, hot-rolled plates, calcium, aluminum, impurities
References

1. Golubtsov V. A., Roshchin V. E., Zinchenko S. D., Voronin A. A. Metallurg — Metallurgist. 2005. No. 4. pp. 73– 77.
2. Bale C. W., Chartrand P., Degterov S. A., Eriksson G., Hack K., Ben Mahfoud R., Melançon J., Pelton A. D. and Petersen S. FactSage Thermochemical Software and Databases. Calphad. 2002. Vol. 26, No. 2. pp. 189–228.
3. Dub A. V., Barulenkova N. V., Morozova T. V., Efimov S. V., Filatov V. N., Zinchenko S. D., Lamukhin A. M. Metallurg — Metallurgist. 2004. No. 4. pp. 67–73.
4. Kazakov A. A, Kovalev P. V., Ryaboshuk S. V., Mileykovskiy A. B., Malakhov N. V. Chernye Metally — Ferrous metals. 2009. No. 12. pp. 5–11.
5. Pirozhkova V. P., Yatsenko M. Yu. Stal — Steel in Translation. 2011. No. 3. pp. 24–27.
6. Yo-ichi Ito. Kinetics of Shape Control of Alumina Inclusions with Calcium Treatment in Line Pipe Steel for Sour Service. Tetsu-to-Hagane. 1996. Vol. 93, No. 5. pp. 148–150.
7. Martín A., Brandaleze E. Study about downgrading variables by inclusionary cleanliness in the laddle furnace at ternium side rar. Proceedings of the 7th International Conference on Clean steel. 2007. pp. 203–212.

Language of full-text russian
Full content Buy
Back