Journals →  Chernye Metally →  2013 →  #8

Chernye Metally

Conventional section "Development of metallurgy in Russia and CIS countries" is presented by the article by specialists from the Saint Petersburg State Polytechnical University about dendritic micro-heterogeneity of cast steel. The paper reviews the publications concerning the dependence of dendrite arm spacing of iron-based industrial alloys on the conditions of solidification. In this section another article by specialists of this university isalso presented; it reports about basic ecological parameters of rolling production as the final stage of metallurgical cycle. These values are recommended by ISO 14000 (energy consumption, water consumption, emissions and solid waste) , the system of international certification of environmental performance. Analysis and recommendations for their improvement are given.

The article by specialists of Magnitogorsk State Technical University diescribes the features of forming the structure and properties of welded joints made of K56 steel of via arc welding. The results of comprehensive studies of the effect of arc welding technological procedures on the structure and mechanical properties of the heat affected zone of K56 pipe steel with are presented.

Metallurgy of steelmaking is directly connected with the production of slags. It is noted that high-technological steels can't be produced without slagsUsage of metallurgical slags as raw materials, building materials and fertilizers is observed. In the article by specialists of AG der Dillinger Huttenwerke company in the section "Iron and Steel Making ".

In the same section the article “Traces in alloys and their effect on steelmaking and casting is also published.It describes alloys used to produce the correct steel composition in the steel making plant , undesirable effects, especially casting problems which are observed if the impurities can react with inclusions in the steel. The effect of magnesium in sponge titanium and of oxygen in ferrotitanium are shown.

The section “Rolling” present the article by specialists of SMS Meer company about increased plant availability thanks to optimized roll use in the stretch-reducing mill. The article reportes about innovative technical solution of the design-related and technological characteristics of the process, allowing to cutthe required number of mill stands and to dicrease roll exchange cost.

Also in this section the article “High-efficient descaling with high-pressure accumulator"is published. The paper presents the concept of descaling units with high-pressure accumulators and without them. Potential of power-efficient and resource-saving process is demonstrated.

The Hoesch Hohenlimburg company a producer of a hot-rolled strip of special purpose, meets complicated and permanently changing requirements of customers by means of the advanced quality monitoring system. It provides faster quality control of production. Detailed information on other advantages can be found in the article published in the section "Control, organization and management of production process".

Representatives of many German companies note often friction, intense situations and misunderstanding in relationship with their business partners from other countries. At worst plans on business development are ruined. Often it is explained by wrong expectations, probably, because of ignorance of conventional features of business culture of their partners. Therefore, inoculation of cross-cultural competence becomes more and more important for implementation of strategic development plans of the personnel in the conditions of expansion of the international cooperation. This theme is analysedby B. Dreifert.

You may find below more details about the issue or book printed or electronic version of the journal.

ArticleName Steel industry of the world
Development of metallurgy in Russia and CIS
ArticleName Dendritic micro-heterogeneity of cast steel: review of the problems and their computer-aided analysis (Part 1)
ArticleAuthors V. M. Golod, K. I. Emelyanov, I. G. Orlova.

Chair of Physics and Chemistry of Cast Alloys and Processes, Saint-Petersburg State Polytechnical University (Saint-Petersburg, Russia):

Golod V. M., Cand. Eng., Prof.

Emelyanov K. I., Post-graduate

Orlova I. G., Post-graduate

E-mail (common):

ArticleName Features of forming the structure and properties of welded joints made of steel of K56 strength grade in arc welding
ArticleAuthors A. N. Emelyushin, A. B. Sychkov, A. N. Zavalishin, M. A. Sheksheev

Chair “Material Science and Heat Treatment of Metals”, Magnitogorsk State Technical University named after G. I. Nosov (Magnitogorsk, Russia):

Sychkov A. B., Dr. Eng., Prof.

Zavalishin A. N., Dr. Eng., Prof.

Sheksheev M. A., Post-graduate Student

ArticleName Ecological parameters of rolling production
ArticleAuthors V. Butorina, Yu. Ulamov.

Saint-Petersburg State Polytechnical University (Saint-Petersburg, Russia):

Butorina I., Dr. Eng., Prof., e-mail:

Ulamov Yu., Post-Graduate Student

ArticleName 50th anniversary of I. O. Leushin
ArticleName MIEL company: advices about royalty
Iron and Steel Making
ArticleName Slag in the mill work of environmental and resource policy
ArticleAuthors K.-J. Arlt, N. Bannenberg, G. Endemann, H. Motz

AG der Dillinger Hüttenwerke (Dillingen, Germany):

Arlt K.-J., Dr. Eng., Head of Environment Protection Direction

Bannenberg N., Dr. Eng., Head of Technical Dept.


“Steel” Economical Corporation (Düsseldorf, Germany):

Endemann G., Mag. Eng., Head of “Politics” Business Direction, e-mail:


Institute of Study of Building Materials (Duisburg, Germany):

Motz H., Dr. Eng., CEO

ArticleName Traces in alloys and their effect on steelmaking and casting
ArticleAuthors W. Tiekink, A. Overbosch, P. Broersen, L. Alders, R. Kooter, M. Rijnders.

Tata Steel Technical (Ijmuiden, Netherlands):

Tiekink W., Dr. Eng., e-mail:

Overbosch A., Doct. Cand.

Broersen P., Eng.

Alders L., Mag. Eng.


Tata Steel Strip Products Mainland Europe (Ijmuiden, Netherlands):

Kooter R., Eng.


Tata Steel Research and Development IJTC (Ijmuiden, Netherlands):

Rijnders M., Dr.

ArticleName Demand and supply of ferrous scrap — a changing balance
ArticleAuthor P. Tardy

Association of Hungarian Steel Industry (Budapest, Hungary)

Tardy P., Prof., Dr. Eng., Senior Consultant, e-mail:

ArticleName Increased plant availability thanks to optimized roll use in the stretch-reducing mill
ArticleAuthors H. Neumann, E. Steffen, P. Thieven

SMS Meer GmbH (Monchengladbach, Germany):

Neumann H., Expert in Tube Rolling Equipment

Steffen E., Mag. Eng., Distribution of Seamless Tube Production Equipment

Thieven P., Dr. Eng., Seamless Tubes Production Technology, e-mail:

ArticleName High-efficient descaling with high-pressure accumulator
ArticleAuthors P. Pawlitzki, R. Rehbein

Schafer & Urbach GmbH (Ratingen, Germany)

Pawlitzki P. Mag. Eng.

Rehbein R. Mag. Eng.

Control, organization and management of production process
ArticleName Solution of Manufacturing Intelligence: cutting the expenses for data processing
ArticleAuthors L. Eykmann, U. Duske
ArticleName Steel production worldwide
Education and training of personnel
ArticleName Strategy of personnel development in the conditions of business globalization
ArticleAuthor B. Dreifert
ArticleName 175th anniversary of Ferdinand von Zeppelin
Metallurgical history
ArticleName Steel writes history
ArticleAuthor A. Schwartz
Journals →  Chernye Metally →  2013 →  #8